voxl-streamer client repetitive connect/disconnect

[Eric Katzfey]

@wilkinsaf No, you shouldn't need any drivers. Any USB device should be listed with lsusb, even without any specific drivers. Does it show up when plugged into a regular Linux computer?

[wilkinsaf]

@Eric-Katzfey Yes, we have hardwired it into a computer before. We have seen the stream using ffmpeg on VOXL as well. We just can not seem to get voxl-streamer to work with it

[Eric Katzfey]

@wilkinsaf If you unplug the camera from Voxl does anything disappear from the lsusb list?

[wilkinsaf]

@Eric-Katzfey

Yes, the top 3 entries in lsusb screenshots above are all cameras. I can unplug those one by one and see them disappear.
Would it matter if we have 2 UVC cameras?

[Eric Katzfey]

@wilkinsaf Just try one at a time for now. And when you plug the camera in do you see a new /dev/videoX entry appear?

[Eric Katzfey]

@wilkinsaf Also, were you able to get the ordering information for these cameras? If they aren't too expensive I would like to order at least one of them to test against.

[wilkinsaf]

@Eric-Katzfey

Yes, let me try one at a time now.
Here are the two cameras


1. Banggood URL

2. Blue Robotics URL

[wilkinsaf]

@Eric-Katzfey

Good news, I was able to get voxl-uvc-server to spin up with one usb camera connected.

However, I am getting this issue from voxl-streamer

Seems like I need to figure out the frame size and set the correct one. Let me play around with that now

[wilkinsaf]

@Eric-Katzfey Doesn't look to be frame size as the "sizes" seem non-deterministic

[Eric Katzfey]

@wilkinsaf Great, that's some progress! What about if you try the other camera? Not sure why the frame length is different. For a given resolution and frame format that number should be a constant. (e.g. 640 x 480 x 2).

[wilkinsaf]

@Eric-Katzfey

Good suggestion. Let me try that.
Check out the length when uvc server fires up

Got frame callback! frame_format = 3, width = 640, height = 480, length = 613376, ptr = 0

interesting

[Eric Katzfey]

@wilkinsaf You can try modifying this line in voxl-uvc-server: https://gitlab.com/voxl-public/modal-pipe-architecture/voxl-uvc-server/-/blob/dev/src/main.c#L83

Make it read: .size_bytes = 614400, \

Then rebuild it and try again.

[wilkinsaf]

@Eric-Katzfey Sounds good.

The other camera is giving me this error

The one I compiled could not find the device at all

[Eric Katzfey]

@wilkinsaf Perhaps you are working on master branch? The latest and greatest (The one you should be using) is the dev branch.

[Eric Katzfey]

@wilkinsaf Thanks! I'm going to order them so that I can have them as part of our normal USB UVC camera test suite.

[wilkinsaf]

@Eric-Katzfey Thanks Eric!

I switched to dev branch (slightly embarrassing as you told me to switch to dev) and pull

voxl:~/voxl-uvc-server(dev)$ git pull origin dev
From https://gitlab.com/voxl-public/modal-pipe-architecture/voxl-uvc-server
 * branch            dev        -> FETCH_HEAD
Already up-to-date.

I made sure to install the correct libuvc ipk

voxl:~$ opkg install libuvc_1.0.2_202112182223.ipk
Collected errors:
* opkg_prepare_file_for_install: Refusing to load file 'libuvc_1.0.2_202112182223.ipk' as it matches the installed version of libuvc (1.0.2).

I then built the voxl-uvc-server, ran Makefile, and tried to run

[Eric Katzfey]

@wilkinsaf Okay, interesting. Let's go back to the original camera with the incorrect size. Can you add the patch I suggested and see if you can make that camera work?

[wilkinsaf]

@Eric-Katzfey ope, almost forgot. Yes, let me do that now

[wilkinsaf]

@Eric-Katzfey

For some reason now it is still struggling to find any device. I tried both cameras

[wilkinsaf]

@Eric-Katzfey

I know that it is there as ffmpeg picks up on it