• Categories
  • Recent
  • Tags
  • Popular
  • Users
  • Groups
  • Register
  • Login
ModalAI Forum
  • Categories
  • Recent
  • Tags
  • Popular
  • Users
  • Groups
    • Register
    • Login

    Starling Drone not showing up in ADB devices

    Ask your questions right here!
    starling2 usb voxl linux help
    4
    23
    1.7k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • I
      ijones2 @ijones2
      last edited by 28 Aug 2024, 16:53

      @ijones2 @tom
      Screenshot 2024-08-28 125110.jpg

      T 1 Reply Last reply 28 Aug 2024, 17:03 Reply Quote 0
      • T
        tom admin @ijones2
        last edited by 28 Aug 2024, 17:03

        @ijones2 I would try opening a new terminal, running sudo dmesg -wH, then powering and plugging in your VOXL 2 to your host PC and see if you see any enumeration info come through. This will tell us if your cable setup is good

        I 1 Reply Last reply 29 Aug 2024, 00:48 Reply Quote 0
        • I
          ijones2 @tom
          last edited by 29 Aug 2024, 00:48

          @tom

          Hey Tom!

          I ran the code and I got a lot of input but I went and scrolled specifically to the usb part and here's what I got

          IMG_2229-min.jpg

          IMG_2233-min.jpg

          I can send a picture of all the output it's a lot but let me know if that will be helpful.

          T 1 Reply Last reply 29 Aug 2024, 00:58 Reply Quote 0
          • T
            tom admin @ijones2
            last edited by 29 Aug 2024, 00:58

            @ijones2 Can you try without running anything else? Just plugging in the board and powering it on should spit out some messages if it's detected correctly

            I 1 Reply Last reply 29 Aug 2024, 02:05 Reply Quote 0
            • I
              ijones2 @tom
              last edited by 29 Aug 2024, 02:05

              @tom

              Hey Tom!

              Here'd what I got!

              Screenshot from 2024-08-28 21-55-12-min.png

              Screenshot from 2024-08-28 21-42-44-min.png

              Screenshot from 2024-08-28 21-44-21-min.png

              Screenshot from 2024-08-28 21-43-34-min.png

              T 1 Reply Last reply 29 Aug 2024, 18:01 Reply Quote 0
              • T
                tom admin @ijones2
                last edited by 29 Aug 2024, 18:01

                @ijones2 I'm not seeing any devices that seem to be the drone enumerating. Do you happen to have another machine or USB cable setup you can test with?

                I 2 Replies Last reply 29 Aug 2024, 20:14 Reply Quote 0
                • I
                  ijones2 @tom
                  last edited by 29 Aug 2024, 20:14

                  @tom

                  Hey Tom!

                  I have ordered another USB-C to USB-A cable and made sure that it included data transfer and should be here tomorrow. The cable I am currently using has/had worked but I am starting to think it might be the cord. I will find out tomorrow when it arrives and will update you then! If the new cords do not work on my lab laptop, I will try the cords on a different PC and if THAT does not work...😥

                  1 Reply Last reply Reply Quote 0
                  • I
                    ijones2 @tom
                    last edited by 30 Aug 2024, 15:39

                    @tom

                    Hey Tom! i think this is progress?
                    I tried 3 different USB-C to USB-A cords and the third one gave me " Bus 002 Device 002: ID 05c6:9008 Qualcomm, Inc. Gobi Wireless Modem (QDL mode) "

                    so I guess it was the cord? Or is it my lab laptop?

                    Screenshot from 2024-08-30 11-35-38-min.png

                    I kind of don't know what to make of this??

                    T 1 Reply Last reply 30 Aug 2024, 16:33 Reply Quote 0
                    • T
                      tom admin @ijones2
                      last edited by 30 Aug 2024, 16:33

                      @ijones2 QDL means that the QDL switch is likely switched to ON which would meant that the QDL unbricking process would likely work. Can you try the same test with the switch OFF (requires plugging/unplugging power) and see what lsusb shows?

                      I 1 Reply Last reply 4 Sept 2024, 15:09 Reply Quote 0
                      • I
                        ijones2 @tom
                        last edited by 4 Sept 2024, 15:09

                        @tom

                        Hey Tom! good news!

                        I got new cables for the drone now and when I connected the drone it shows up on the lsusb and I am able to run the adb shell. Would I have to unbrick it or because the adb shell is running I would not need to unbrick it? Essentially I'm asking what my next steps should be?

                        Screenshot from 2024-09-04 11-07-26-min.png

                        T 1 Reply Last reply 4 Sept 2024, 16:18 Reply Quote 0
                        • T
                          tom admin @ijones2
                          last edited by 4 Sept 2024, 16:18

                          @ijones2 This is great news! It looks like everything is functioning as expected so no need to go through the unbricking process at this point.

                          It does appear that there is a fairly old SDK loaded on there so I would recommend flashing the latest SDK (1.3.3) from downloads.modalai.com under "VOXL 2 Platform Releases"

                          Just follow the instructions here to do so: https://docs.modalai.com/flash-system-image/#flashing-a-voxl-sdk-release

                          1 Reply Last reply Reply Quote 0
                          13 out of 23
                          • First post
                            13/23
                            Last post
                          Powered by NodeBB | Contributors