Sony RXO over USB
-
@tom is the VOXL streamer apk required in order to use the gphoto2 to stream video?
-
@Matt-Goddard We have two different implementations for gphoto2 on VOXL.
voxl-libgphoto2which is what you are using and we also havevoxl-gphoto2which is a newer version that also usesvoxl-streamer. I think I will have you tryvoxl-gphoto2now.Here is the link to the build/install instructions for the newer gphoto2 implementation.
Here is a link to the documentation
You will need to use this in combination with voxl-streamer and here is some documentation for getting that going.
-
I will try this now and get back to you. Thanks!
-
During the process, we managed to brick the board. Will not boot now..
-
@Matt-Goddard We have some documentation on unbricking here
-
Got it, we will order the part and unbrick lol. Thanks for the help!
-
The USB and Serial Debug board arrived today. I unbricked the board and installed gphoto2 and VOXL-streamer. The image below is an error I received after running the voxl-gphoto2 command.
Please advise.
-
Have you tried gphoto2 using a Linux machine to make sure this device is supported?
-
@Matt-Goddard said in Sony RXO over USB:
Sony RXO
The RX0 II is on the list, is that what you're using?
http://www.gphoto.org/proj/libgphoto2/support.php -
Yes we are attempting to use the RX0. The image below shows that gphoto2 does detect it on an ubuntu machine.
-
@Aaron-Bottke What happens when you run
gphoto2 --capture-preview? Do you get an image? -
@Aaron-Bottke Also, can you try running voxl-gphoto2 with debugging information enabled and send us the ouput? For example:
voxl-gphoto2 -d -v -g -
Results of gphoto2 --capture-preview on my host machine as follows.
On the VOXL running voxl-gphoto2 -d -v -g yields way to much for me to share here so I will split it up.
voxl-gphoto2 -d below.
voxl-gphoto2 -v yields a lot of messages very quickly.
Output as follows.
voxl-gphoto2 -v yields too many messages for me to upload with a screenshot.
I don't see a way to submit a .txt file but the most interesting part of the output that I see is this.
-
@Aaron-Bottke Okay, thanks! That's very helpful information. It looks like the camera is producing images and voxl-gphoto2 is processing them correctly. So try voxl-streamer and see if you can stream the video. That error message seems to be coming from the gphoto2 library but doesn't seem to be hurting anything.
-
Unless I am missing something in the command this is the result from running voxl-streamer and voxl-gphoto2.
Thanks for all the help.
-
@Aaron-Bottke Documentation on voxl-streamer is here: https://docs.modalai.com/voxl-streamer/
For gphoto2 you will want to look at the
gphoto2-mpaconfiguration in/etc/modalai/voxl-streamer.conf. You can use this configuration record by launching withvoxl-streamer -c gphoto2-mpa -
That got it working!!! I really appreciate the help with this!!!
My telemetry quit working though so I have to play with that and get that up and running again.
Thanks! -
The gphoto-2 seams to be breaking the voxl-vision-px4 system. Any command associated with the voxl-vision-px4 system causes the voxl to kick any adb connection then prevent any from connecting until a power cycle. I can't get both voxl-vision-px4 and gphoto2 installed and running on the same system.
Any thoughts?
Thanks, -
@Aaron-Bottke I'll take a look
-
@Aaron-Bottke I did a fresh install of system image 3.2.0 without installing any additional packages (voxl-suite). After setting up WiFi to connect to the Internet I ran these steps on voxl (over adb):
- opkg update
- opkg install voxl-vision-px4
- voxl-configure-vision-px4 (Specifying no cameras)
- Verify QGC connection with telemetry
- opkg install voxl-gphoto2
- opkg install voxl-streamer
- voxl-gphoto2
- voxl-streamer -c gphoto2-mpa
I then see both telemetry and video in QGC.
