Skip to content
  • Categories
  • Recent
  • Tags
  • Popular
  • Users
  • Groups
Collapse
Brand Logo

ModalAI Forum

V

vamsi

@vamsi
Contributor
Unfollow Follow
About
Posts
13
Topics
4
Shares
0
Groups
1
Followers
0
Following
1

Posts

Recent Best Controversial

  • Starling 2 Max Drone drifting off
    V vamsi

    @Eric-Katzfey

    Thank you for your response.

    For Manual mode, I recalibrated the level horizon, accel, compass, and gyro. However, during the RC calibration, I noticed a small shift in the yaw when all the sticks are in their neutral positions. I’m unsure if this is contributing to the issue. I attempted to recalibrate it several times, but the yaw does not reset to the 0 position. Please find the attached screenshot for your reference:
    ca3710fa-d00c-4444-b9cf-2fe8d267f7f4-image.png .

    As you suggested, I tried flying in Altitude Hold mode, and the drone drifted in the direction where the yaw was shifted.

    Is there a way to fix the yaw offset?

    Ask your questions right here!

  • Starling 2 Max Not Arming
    V vamsi

    @Eric-Katzfey

    Nevermind, I found the issue. In the voxl-px4.conf file, the RC value was somehow updated to SPEKTRUM. After changing the RC value back to GHST, the issue was resolved.

    Thank you so much for your support!

    Ask your questions right here!

  • Starling 2 Max Not Arming
    V vamsi

    @Eric-Katzfey

    When I checked the Voxl Health Check via the Voxl portal, I noticed that the health check had failed, as shown in the attached images:

    b0288d92-86ca-40d0-8b5a-88c0588a690f-image.png

    83810237-5c7a-47ad-bd00-b068d234a33d-image.png

    I am using indoor GPS-denied navigation, so the GPS sensor status is correctly marked as false. However, I have turned on my Remote Controller, yet the input_rc status still shows as false.

    Additionally, when I change the mode using the Remote Controller, QGroundControl does not reflect the mode changes. The same issue occurs with the kill switch—engaging or disengaging it does not update in QGC.

    I am using the Ghost RC that I got from ModalAI. I suspect I might have unknowingly made changes to the QGC radio settings. Could this be the cause of the issue, and if so, what steps should I take to verify or correct this?

    Ask your questions right here!

  • Starling 2 Max Not Arming
    V vamsi

    Hi @Eric-Katzfey,

    Thank you for your response.

    When I connect to QGroundControl (QGC), the reason for the failure to arm is shown as follows:

    af72e7a5-d06b-4cde-9887-f489a1eb53ab-image.png

    9ec8bf16-a1e4-4e79-a90d-a93dabdb0393-image.png

    Additionally, here are the outputs when I run the voxl-px4 and voxl-px4-start commands:

    voxl2:~$ voxl-px4
    [INFO] Reading from /etc/modalai/voxl-px4.conf
    Found DSP signature file
    [INFO] Daemon mode enabled


    AIRFRAME=MULTICOPTER
    GPS=NONE
    RC=SPEKTRUM
    ESC=VOXL_ESC
    POWER MANAGER=VOXLPM
    AIRSPEED SENSOR=NONE
    DISTANCE SENSOR=NONE
    OSD=DISABLE
    DAEMON_MODE=ENABLE
    SENSOR_CAL=ACTUAL
    ARTIFACT_MODE=DISABLE
    EXTRA STEPS:


    INFO [px4] mlockall() enabled. PX4's virtual address space is locked into RAM.
    INFO [px4] PX4 server already running for instance 0

    voxl2:~$ voxl-px4-start


    AIRFRAME:
    GPS:
    RC:
    ESC:
    POWER MANAGER:
    AIRSPEED SENSOR:
    DISTANCE SENSOR:
    OSD:
    ARTIFACT_MODE:
    EXTRA STEPS:


    Running on M0054
    INFO [param] selected parameter default file /data/px4/param/parameters
    INFO [parameters] BSON document size 3366 bytes, decoded 3366 bytes (INT32:48, FLOAT:107)
    ERROR [logger] Task already running
    Starting IMU driver with no rotation
    INFO [qshell] Send cmd: 'icm42688p start -s'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 804961172, local time: 804964507
    ERROR [qshell] Command failed
    INFO [qshell] Send cmd: 'icp101xx start -I -b 5'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 804991878, local time: 804994336
    ERROR [qshell] Command failed
    Looking for qmc5883l magnetometer
    INFO [qshell] Send cmd: 'qmc5883l start -R 10 -X -b 1'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805029897, local time: 805032559
    ERROR [qshell] Command failed
    Looking for ist8310 magnetometer
    INFO [qshell] Send cmd: 'ist8310 start -R 10 -X -b 1'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805068252, local time: 805069440
    ERROR [qshell] Command failed
    INFO [qshell] Send cmd: 'gps start'
    INFO [qshell] qshell return value timestamp: 805101426, local time: 805103077
    Looking for ncp5623c RGB LED
    INFO [qshell] Send cmd: 'rgbled_ncp5623c start -X -b 1 -f 400 -a 56'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805142844, local time: 805145634
    ERROR [qshell] Command failed
    No ESC type specified, not starting an ESC driver
    INFO [qshell] Send cmd: 'sensors start'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805268907, local time: 805270932
    ERROR [qshell] Command failed
    INFO [qshell] Send cmd: 'ekf2 start'
    INFO [qshell] qshell return value timestamp: 805300354, local time: 805305054
    /usr/bin/voxl-px4-start: line 215: [: =: unary operator expected
    INFO [qshell] Send cmd: 'manual_control start'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805334289, local time: 805336988
    ERROR [qshell] Command failed
    INFO [qshell] Send cmd: 'control_allocator start'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805374536, local time: 805378458
    ERROR [qshell] Command failed
    INFO [qshell] Send cmd: 'load_mon start'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805413929, local time: 805416679
    ERROR [qshell] Command failed
    INFO [qshell] Send cmd: 'rc_update start'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805448866, local time: 805449872
    ERROR [qshell] Command failed
    INFO [qshell] Send cmd: 'commander start'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805489289, local time: 805490118
    ERROR [qshell] Command failed
    INFO [qshell] Send cmd: 'flight_mode_manager start'
    INFO [qshell] cmd returned with: -1
    INFO [qshell] qshell return value timestamp: 805528214, local time: 805531157
    ERROR [qshell] Command failed
    WARN [dataman] dataman already running
    ERROR [navigator] Task already running
    ERROR [load_mon] Task already running
    WARN [modal_io_bridge] Already started
    ERROR [microdds_client] Task already running
    INFO [mavlink] MAVLink only on localhost (set param MAV_{i}_BROADCAST = 1 to enable network)
    voxl2:~$

    Additionally, after running the voxl-esc disable_bridge command, do I need to enable any specific ports or perform additional configurations to ensure proper communication between the modules?

    Thank you for your assistance!

    Ask your questions right here!

  • Starling 2 Max Drone drifting off
    V vamsi

    Hi @Eric-Katzfey, Thank you for your response and for pointing out potential issues.

    1. Yes, when I fly with the RC in Position mode and Offboard mode, it works fine.

    2. In Manual mode, the drone is completely unflyable. When I try to take off, it drifts aggressively to one side. The logs attached in my initial comment were recorded during an attempt to take off from the ground.

    3. Yes, the MAVSDK program I mentioned was the only one I was running at the time.

    4. Oh, is there a way to disable the Offboard figure-8 commands from voxl-vision-hub? (Edit: do I need to update "/etc/modalai/voxl-vision-hub.conf" and set "offboard_mode": "off"? Is this enough to turn off the figure 8 mode?)

    Thank you for your support!

    Ask your questions right here!

  • Starling 2 Max Not Arming
    V vamsi

    Hi Team,

    I am currently facing an issue where I am unable to arm the drone, either through the Remote Controller or via the MAVSDK program. I am unsure of the root cause of this problem.

    I was troubleshooting a drift issue during Offboard flight mode when running the MAVSDK program. To check if it was related to ESC calibration, I followed the instructions provided in the following resources:

    https://docs.modalai.com/modal-esc-v2-manual/
    https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/blob/master/voxl-esc-tools/calibration.md

    After checking the calibration, I ran the voxl-esc disable_bridge command, enabled Voxl-PX4, and rebooted Voxl. However, since then, I have been unable to arm the drone.

    I have verified that all the required services are running, as shown in the attached screenshot:
    012c1420-e943-44f6-a006-046b1dee1e4f-image.png

    The below are the PX4-Params:
    voxl2:/$ px4-param show
    Symbols: x = used, + = saved, * = unsaved
    x ASPD_SCALE_1 [0,23] : 1.0000
    x + BAT1_CAPACITY [1,42] : 3950.0000
    x + BAT1_N_CELLS [2,45] : 4
    x + BAT1_R_INTERNAL [3,46] : 0.0220
    x BAT1_SOURCE [4,48] : 0
    x + BAT1_V_CHARGED [5,50] : 4.1000
    x + BAT1_V_EMPTY [6,52] : 2.8000
    x BAT1_V_LOAD_DROP [7,53] : 0.1000
    x + BAT_AVRG_CURRENT [8,68] : 3.4000
    x + BAT_CRIT_THR [9,69] : 0.1000
    x BAT_EMERGEN_THR [10,70] : 0.0500
    x BAT_LOW_THR [11,71] : 0.1500
    x BAT_N_CELLS [12,72] : 3
    x BAT_V_CHARGED [13,73] : 4.0500
    x BAT_V_EMPTY [14,74] : 3.6000
    x BAT_V_LOAD_DROP [15,75] : 0.3000
    x + CAL_ACC0_ID [16,77] : 2490378
    x + CAL_ACC0_PRIO [17,78] : 50
    x CAL_ACC0_ROT [18,79] : -1
    x + CAL_ACC0_XOFF [19,80] : -0.0110
    x + CAL_ACC0_XSCALE [20,81] : 1.0073
    x + CAL_ACC0_YOFF [21,82] : -0.0074
    x + CAL_ACC0_YSCALE [22,83] : 1.0054
    x + CAL_ACC0_ZOFF [23,84] : -0.0661
    x + CAL_ACC0_ZSCALE [24,85] : 1.0079
    x CAL_ACC1_ID [25,86] : 0
    x CAL_ACC2_ID [26,95] : 0
    x CAL_ACC3_ID [27,104] : 0
    x CAL_AIR_CMODEL [28,113] : 0
    x CAL_AIR_TUBED_MM [29,114] : 1.5000
    x CAL_AIR_TUBELEN [30,115] : 0.2000
    x CAL_BARO0_ID [31,116] : 0
    x CAL_BARO1_ID [32,119] : 0
    x CAL_BARO2_ID [33,122] : 0
    x CAL_BARO3_ID [34,125] : 0
    x + CAL_GYRO0_ID [35,128] : 2490378
    x + CAL_GYRO0_PRIO [36,129] : 50
    x CAL_GYRO0_ROT [37,130] : -1
    x + CAL_GYRO0_XOFF [38,131] : 0.0035
    x + CAL_GYRO0_YOFF [39,132] : 0.0076
    x + CAL_GYRO0_ZOFF [40,133] : 0.0076
    x CAL_GYRO1_ID [41,134] : 0
    x CAL_GYRO2_ID [42,140] : 0
    x CAL_GYRO3_ID [43,146] : 0
    x + CAL_MAG0_ID [44,152] : 527625
    x + CAL_MAG0_PRIO [45,153] : 75
    x + CAL_MAG0_ROT [46,154] : 0
    x CAL_MAG0_XCOMP [47,155] : 0.0000
    x + CAL_MAG0_XODIAG [48,156] : 0.0610
    x + CAL_MAG0_XOFF [49,157] : -0.1331
    x + CAL_MAG0_XSCALE [50,158] : 0.9220
    x CAL_MAG0_YCOMP [51,159] : 0.0000
    x + CAL_MAG0_YODIAG [52,160] : -0.0123
    x + CAL_MAG0_YOFF [53,161] : -0.0037
    x + CAL_MAG0_YSCALE [54,162] : 0.9370
    x CAL_MAG0_ZCOMP [55,163] : 0.0000
    x + CAL_MAG0_ZODIAG [56,164] : 0.0177
    x + CAL_MAG0_ZOFF [57,165] : -0.1041
    x + CAL_MAG0_ZSCALE [58,166] : 1.0706
    x CAL_MAG1_ID [59,167] : 0
    x CAL_MAG1_ROT [60,169] : -1
    x CAL_MAG2_ID [61,182] : 0
    x CAL_MAG2_ROT [62,184] : -1
    x CAL_MAG3_ID [63,197] : 0
    x CAL_MAG3_ROT [64,199] : -1
    x CA_AIRFRAME [65,224] : 0
    x CA_FAILURE_MODE [66,225] : 0
    x CA_METHOD [67,240] : 2
    x CA_R0_SLEW [68,241] : 0.0000
    x CA_R10_SLEW [69,242] : 0.0000
    x CA_R11_SLEW [70,243] : 0.0000
    x CA_R1_SLEW [71,244] : 0.0000
    x CA_R2_SLEW [72,245] : 0.0000
    x CA_R3_SLEW [73,246] : 0.0000
    x CA_R4_SLEW [74,247] : 0.0000
    x CA_R5_SLEW [75,248] : 0.0000
    x CA_R6_SLEW [76,249] : 0.0000
    x CA_R7_SLEW [77,250] : 0.0000
    x CA_R8_SLEW [78,251] : 0.0000
    x CA_R9_SLEW [79,252] : 0.0000
    x CA_ROTOR0_AX [80,253] : 0.0000
    x CA_ROTOR0_AY [81,254] : 0.0000
    x CA_ROTOR0_AZ [82,255] : -1.0000
    x CA_ROTOR0_CT [83,256] : 6.5000
    x CA_ROTOR0_KM [84,257] : 0.0500
    x + CA_ROTOR0_PX [85,258] : 0.0850
    x + CA_ROTOR0_PY [86,259] : 0.0625
    x CA_ROTOR0_PZ [87,260] : 0.0000
    x CA_ROTOR10_AX [88,262] : 0.0000
    x CA_ROTOR10_AY [89,263] : 0.0000
    x CA_ROTOR10_AZ [90,264] : -1.0000
    x CA_ROTOR10_CT [91,265] : 6.5000
    x CA_ROTOR10_KM [92,266] : 0.0500
    x CA_ROTOR10_PX [93,267] : 0.0000
    x CA_ROTOR10_PY [94,268] : 0.0000
    x CA_ROTOR10_PZ [95,269] : 0.0000
    x CA_ROTOR11_AX [96,271] : 0.0000
    x CA_ROTOR11_AY [97,272] : 0.0000
    x CA_ROTOR11_AZ [98,273] : -1.0000
    x CA_ROTOR11_CT [99,274] : 6.5000
    x CA_ROTOR11_KM [100,275] : 0.0500
    x CA_ROTOR11_PX [101,276] : 0.0000
    x CA_ROTOR11_PY [102,277] : 0.0000
    x CA_ROTOR11_PZ [103,278] : 0.0000
    x CA_ROTOR1_AX [104,280] : 0.0000
    x CA_ROTOR1_AY [105,281] : 0.0000
    x CA_ROTOR1_AZ [106,282] : -1.0000
    x CA_ROTOR1_CT [107,283] : 6.5000
    x CA_ROTOR1_KM [108,284] : 0.0500
    x + CA_ROTOR1_PX [109,285] : -0.0850
    x + CA_ROTOR1_PY [110,286] : -0.0625
    x CA_ROTOR1_PZ [111,287] : 0.0000
    x CA_ROTOR2_AX [112,289] : 0.0000
    x CA_ROTOR2_AY [113,290] : 0.0000
    x CA_ROTOR2_AZ [114,291] : -1.0000
    x CA_ROTOR2_CT [115,292] : 6.5000
    x + CA_ROTOR2_KM [116,293] : -0.0500
    x + CA_ROTOR2_PX [117,294] : 0.0850
    x + CA_ROTOR2_PY [118,295] : -0.0625
    x CA_ROTOR2_PZ [119,296] : 0.0000
    x CA_ROTOR3_AX [120,298] : 0.0000
    x CA_ROTOR3_AY [121,299] : 0.0000
    x CA_ROTOR3_AZ [122,300] : -1.0000
    x CA_ROTOR3_CT [123,301] : 6.5000
    x + CA_ROTOR3_KM [124,302] : -0.0500
    x + CA_ROTOR3_PX [125,303] : -0.0850
    x + CA_ROTOR3_PY [126,304] : 0.0625
    x CA_ROTOR3_PZ [127,305] : 0.0000
    x CA_ROTOR4_AX [128,307] : 0.0000
    x CA_ROTOR4_AY [129,308] : 0.0000
    x CA_ROTOR4_AZ [130,309] : -1.0000
    x CA_ROTOR4_CT [131,310] : 6.5000
    x CA_ROTOR4_KM [132,311] : 0.0500
    x CA_ROTOR4_PX [133,312] : 0.0000
    x CA_ROTOR4_PY [134,313] : 0.0000
    x CA_ROTOR4_PZ [135,314] : 0.0000
    x CA_ROTOR5_AX [136,316] : 0.0000
    x CA_ROTOR5_AY [137,317] : 0.0000
    x CA_ROTOR5_AZ [138,318] : -1.0000
    x CA_ROTOR5_CT [139,319] : 6.5000
    x CA_ROTOR5_KM [140,320] : 0.0500
    x CA_ROTOR5_PX [141,321] : 0.0000
    x CA_ROTOR5_PY [142,322] : 0.0000
    x CA_ROTOR5_PZ [143,323] : 0.0000
    x CA_ROTOR6_AX [144,325] : 0.0000
    x CA_ROTOR6_AY [145,326] : 0.0000
    x CA_ROTOR6_AZ [146,327] : -1.0000
    x CA_ROTOR6_CT [147,328] : 6.5000
    x CA_ROTOR6_KM [148,329] : 0.0500
    x CA_ROTOR6_PX [149,330] : 0.0000
    x CA_ROTOR6_PY [150,331] : 0.0000
    x CA_ROTOR6_PZ [151,332] : 0.0000
    x CA_ROTOR7_AX [152,334] : 0.0000
    x CA_ROTOR7_AY [153,335] : 0.0000
    x CA_ROTOR7_AZ [154,336] : -1.0000
    x CA_ROTOR7_CT [155,337] : 6.5000
    x CA_ROTOR7_KM [156,338] : 0.0500
    x CA_ROTOR7_PX [157,339] : 0.0000
    x CA_ROTOR7_PY [158,340] : 0.0000
    x CA_ROTOR7_PZ [159,341] : 0.0000
    x CA_ROTOR8_AX [160,343] : 0.0000
    x CA_ROTOR8_AY [161,344] : 0.0000
    x CA_ROTOR8_AZ [162,345] : -1.0000
    x CA_ROTOR8_CT [163,346] : 6.5000
    x CA_ROTOR8_KM [164,347] : 0.0500
    x CA_ROTOR8_PX [165,348] : 0.0000
    x CA_ROTOR8_PY [166,349] : 0.0000
    x CA_ROTOR8_PZ [167,350] : 0.0000
    x CA_ROTOR9_AX [168,352] : 0.0000
    x CA_ROTOR9_AY [169,353] : 0.0000
    x CA_ROTOR9_AZ [170,354] : -1.0000
    x CA_ROTOR9_CT [171,355] : 6.5000
    x CA_ROTOR9_KM [172,356] : 0.0500
    x CA_ROTOR9_PX [173,357] : 0.0000
    x CA_ROTOR9_PY [174,358] : 0.0000
    x CA_ROTOR9_PZ [175,359] : 0.0000
    x + CA_ROTOR_COUNT [176,361] : 4
    x CA_R_REV [177,362] : 0
    x CA_SV0_SLEW [178,372] : 0.0000
    x CA_SV1_SLEW [179,373] : 0.0000
    x CA_SV2_SLEW [180,374] : 0.0000
    x CA_SV3_SLEW [181,375] : 0.0000
    x CA_SV4_SLEW [182,376] : 0.0000
    x CA_SV5_SLEW [183,377] : 0.0000
    x CA_SV6_SLEW [184,378] : 0.0000
    x CA_SV7_SLEW [185,379] : 0.0000
    x CBRK_AIRSPD_CHK [186,454] : 0
    x CBRK_FLIGHTTERM [187,456] : 121212
    x CBRK_IO_SAFETY [188,457] : 22027
    x + CBRK_SUPPLY_CHK [189,458] : 894281
    x CBRK_USB_CHK [190,459] : 197848
    x CBRK_VTOLARMING [191,460] : 0
    x COM_ACT_FAIL_ACT [192,461] : 0
    x COM_ARM_ARSP_EN [193,462] : 1
    x COM_ARM_AUTH_ID [194,463] : 10
    x COM_ARM_AUTH_MET [195,464] : 0
    x COM_ARM_AUTH_REQ [196,465] : 0
    x COM_ARM_AUTH_TO [197,466] : 1.0000
    x COM_ARM_BAD_INOV [198,467] : 0
    x COM_ARM_CHK_ESCS [199,468] : 0
    x COM_ARM_EKF_BIAS [200,469] : 3.0000
    x COM_ARM_EKF_HGT [201,470] : 1.0000
    x COM_ARM_EKF_POS [202,471] : 0.5000
    x COM_ARM_EKF_VEL [203,472] : 0.5000
    x COM_ARM_EKF_YAW [204,473] : 0.5000
    x COM_ARM_HFLT_CHK [205,474] : 1
    x COM_ARM_IMU_ACC [206,475] : 0.7000
    x COM_ARM_IMU_GYR [207,476] : 0.2500
    x COM_ARM_MAG_ANG [208,477] : 60
    x COM_ARM_MAG_STR [209,478] : 2
    x COM_ARM_MIS_REQ [210,479] : 0
    x COM_ARM_ODID [211,480] : 0
    x + COM_ARM_SDCARD [212,481] : 0
    x COM_ARM_SWISBTN [213,482] : 0
    x COM_ARM_WO_GPS [214,483] : 1
    x + COM_CPU_MAX [215,484] : -1.0000
    x COM_DISARM_FORCE [216,485] : 0
    x + COM_DISARM_LAND [217,486] : 0.1000
    x + COM_DISARM_PRFLT [218,487] : 20.0000
    x COM_DL_LOSS_T [219,488] : 10
    x COM_FAIL_ACT_T [220,489] : 5.0000
    x + COM_FLIGHT_UUID [221,490] : 275
    x + COM_FLTMODE1 [222,491] : 0
    x + COM_FLTMODE2 [223,492] : 0
    x + COM_FLTMODE3 [224,493] : 2
    x + COM_FLTMODE4 [225,494] : 2
    x + COM_FLTMODE5 [226,495] : 7
    x + COM_FLTMODE6 [227,496] : 7
    x COM_FLT_PROFILE [228,497] : 0
    x COM_FLT_TIME_MAX [229,498] : -1
    x COM_FORCE_SAFETY [230,499] : 0
    x COM_HLDL_LOSS_T [231,500] : 120
    x COM_HLDL_REG_T [232,501] : 0
    x COM_HOME_EN [233,502] : 1
    x COM_HOME_IN_AIR [234,503] : 0
    x COM_IMB_PROP_ACT [235,504] : 0
    x + COM_KILL_DISARM [236,505] : 0.0000
    x COM_LKDOWN_TKO [237,506] : 3.0000
    x COM_LOW_BAT_ACT [238,507] : 0
    x COM_MOT_TEST_EN [239,508] : 1
    x COM_OBC_LOSS_T [240,509] : 5.0000
    x COM_OBL_RC_ACT [241,510] : 0
    x COM_OBS_AVOID [242,511] : 0
    x COM_OF_LOSS_T [243,512] : 1.0000
    x COM_PARACHUTE [244,513] : 0
    x COM_POSCTL_NAVL [245,514] : 0
    x COM_POS_FS_DELAY [246,515] : 1
    x COM_POS_FS_EPH [247,516] : 5.0000
    x COM_POS_LOW_EPH [248,517] : -1.0000
    x COM_POWER_COUNT [249,518] : 1
    x COM_PREARM_MODE [250,519] : 0
    x COM_QC_ACT [251,520] : 0
    x COM_RCL_EXCEPT [252,521] : 0
    x COM_RC_ARM_HYST [253,522] : 1000
    x COM_RC_IN_MODE [254,523] : 3
    x COM_RC_LOSS_T [255,524] : 0.5000
    x COM_RC_OVERRIDE [256,525] : 1
    x COM_RC_STICK_OV [257,526] : 30.0000
    x + COM_SPOOLUP_TIME [258,527] : 2.0000
    x COM_TAKEOFF_ACT [259,528] : 0
    x COM_VEL_FS_EVH [260,529] : 1.0000
    x COM_WIND_MAX [261,530] : -1.0000
    x COM_WIND_WARN [262,531] : -1.0000
    x CP_DELAY [263,532] : 0.4000
    x + CP_DIST [264,533] : -0.3048
    x CP_GO_NO_DATA [265,534] : 0
    x CP_GUIDE_ANG [266,535] : 30.0000
    x EKF2_ABIAS_INIT [267,543] : 0.2000
    x EKF2_ABL_ACCLIM [268,544] : 25.0000
    x EKF2_ABL_GYRLIM [269,545] : 3.0000
    x EKF2_ABL_LIM [270,546] : 0.4000
    x EKF2_ABL_TAU [271,547] : 0.5000
    x EKF2_ACC_B_NOISE [272,548] : 0.0030
    x EKF2_ACC_NOISE [273,549] : 0.3500
    x EKF2_AID_MASK [274,550] : 0
    x EKF2_ANGERR_INIT [275,551] : 0.1000
    x EKF2_ARSP_THR [276,552] : 0.0000
    x EKF2_ASPD_MAX [277,553] : 20.0000
    x EKF2_ASP_DELAY [278,554] : 100.0000
    x EKF2_AVEL_DELAY [279,555] : 5.0000
    x EKF2_BARO_CTRL [280,556] : 1
    x EKF2_BARO_DELAY [281,557] : 0.0000
    x EKF2_BARO_GATE [282,558] : 5.0000
    x EKF2_BARO_NOISE [283,559] : 3.5000
    x EKF2_BCOEF_X [284,560] : 100.0000
    x EKF2_BCOEF_Y [285,561] : 100.0000
    x EKF2_BETA_GATE [286,562] : 5.0000
    x EKF2_BETA_NOISE [287,563] : 0.3000
    x EKF2_DECL_TYPE [288,564] : 7
    x EKF2_DRAG_CTRL [289,565] : 0
    x EKF2_DRAG_NOISE [290,566] : 2.5000
    x EKF2_EAS_NOISE [291,567] : 1.4000
    x EKF2_EVA_NOISE [292,568] : 0.1000
    x EKF2_EVP_GATE [293,569] : 5.0000
    x EKF2_EVP_NOISE [294,570] : 0.1000
    x EKF2_EVV_GATE [295,571] : 3.0000
    x EKF2_EVV_NOISE [296,572] : 0.1000
    x EKF2_EV_CTRL [297,573] : 15
    x EKF2_EV_DELAY [298,574] : 0.0000
    x EKF2_EV_HGT_TO [299,575] : 5000
    x EKF2_EV_NOISE_MD [300,576] : 0
    x EKF2_EV_POS_TO [301,577] : 1000
    x EKF2_EV_POS_X [302,578] : 0.0000
    x EKF2_EV_POS_Y [303,579] : 0.0000
    x EKF2_EV_POS_Z [304,580] : 0.0000
    x + EKF2_EV_QMIN [305,581] : 1
    x EKF2_FUSE_BETA [306,582] : 0
    x EKF2_GBIAS_INIT [307,583] : 0.1000
    x EKF2_GND_EFF_DZ [308,584] : 4.0000
    x EKF2_GND_MAX_HGT [309,585] : 0.5000
    x EKF2_GPS_CHECK [310,586] : 245
    x + EKF2_GPS_CTRL [311,587] : 0
    x EKF2_GPS_DELAY [312,588] : 110.0000
    x EKF2_GPS_POS_X [313,589] : 0.0000
    x EKF2_GPS_POS_Y [314,590] : 0.0000
    x EKF2_GPS_POS_Z [315,591] : 0.0000
    x EKF2_GPS_P_GATE [316,592] : 5.0000
    x EKF2_GPS_P_NOISE [317,593] : 0.5000
    x EKF2_GPS_V_GATE [318,594] : 5.0000
    x EKF2_GPS_V_NOISE [319,595] : 0.3000
    x EKF2_GRAV_NOISE [320,596] : 1.0000
    x EKF2_GSF_TAS [321,597] : 15.0000
    x EKF2_GYR_B_LIM [322,598] : 0.1500
    x EKF2_GYR_B_NOISE [323,599] : 0.0010
    x EKF2_GYR_NOISE [324,600] : 0.0150
    x EKF2_HDG_GATE [325,601] : 2.6000
    x EKF2_HEAD_NOISE [326,602] : 0.3000
    x + EKF2_HGT_REF [327,603] : 3
    x EKF2_IMU_CTRL [328,604] : 3
    x + EKF2_IMU_POS_X [329,605] : 0.0050
    x + EKF2_IMU_POS_Y [330,606] : 0.0080
    x + EKF2_IMU_POS_Z [331,607] : -0.0116
    x EKF2_MAG_ACCLIM [332,608] : 0.5000
    x EKF2_MAG_B_NOISE [333,609] : 0.0001
    x EKF2_MAG_CHECK [334,610] : 1
    x EKF2_MAG_DECL [335,611] : 0.0000
    x EKF2_MAG_DELAY [336,612] : 0.0000
    x EKF2_MAG_E_NOISE [337,613] : 0.0010
    x EKF2_MAG_GATE [338,614] : 3.0000
    x EKF2_MAG_NOISE [339,615] : 0.0500
    x + EKF2_MAG_TYPE [340,616] : 5
    x EKF2_MAG_YAWLIM [341,617] : 0.2000
    x EKF2_MCOEF [342,618] : 0.1500
    x EKF2_MIN_RNG [343,619] : 0.1000
    x EKF2_NOAID_NOISE [344,622] : 10.0000
    x EKF2_NOAID_TOUT [345,623] : 5000000
    x EKF2_OF_CTRL [346,624] : 0
    x EKF2_OF_DELAY [347,625] : 20.0000
    x EKF2_OF_GATE [348,626] : 3.0000
    x EKF2_OF_N_MAX [349,627] : 0.5000
    x EKF2_OF_N_MIN [350,628] : 0.1500
    x EKF2_OF_POS_X [351,629] : 0.0000
    x EKF2_OF_POS_Y [352,630] : 0.0000
    x EKF2_OF_POS_Z [353,631] : 0.0000
    x EKF2_OF_QMIN [354,632] : 1
    x EKF2_PCOEF_XN [355,633] : 0.0000
    x EKF2_PCOEF_XP [356,634] : 0.0000
    x EKF2_PCOEF_YN [357,635] : 0.0000
    x EKF2_PCOEF_YP [358,636] : 0.0000
    x EKF2_PCOEF_Z [359,637] : 0.0000
    x EKF2_PREDICT_US [360,638] : 10000
    x EKF2_REQ_EPH [361,639] : 3.0000
    x EKF2_REQ_EPV [362,640] : 5.0000
    x + EKF2_REQ_GPS_H [363,641] : 5.0000
    x EKF2_REQ_HDRIFT [364,642] : 0.1000
    x EKF2_REQ_NSATS [365,643] : 6
    x EKF2_REQ_PDOP [366,644] : 2.5000
    x + EKF2_REQ_SACC [367,645] : 1.5000
    x EKF2_REQ_VDRIFT [368,646] : 0.2000
    x EKF2_RNG_A_HMAX [369,647] : 5.0000
    x EKF2_RNG_A_IGATE [370,648] : 1.0000
    x EKF2_RNG_A_VMAX [371,649] : 1.0000
    x + EKF2_RNG_CTRL [372,650] : 0
    x EKF2_RNG_DELAY [373,651] : 5.0000
    x EKF2_RNG_GATE [374,652] : 5.0000
    x EKF2_RNG_K_GATE [375,653] : 1.0000
    x EKF2_RNG_NOISE [376,654] : 0.1000
    x EKF2_RNG_PITCH [377,655] : 0.0000
    x EKF2_RNG_POS_X [378,656] : 0.0000
    x EKF2_RNG_POS_Y [379,657] : 0.0000
    x EKF2_RNG_POS_Z [380,658] : 0.0000
    x EKF2_RNG_QLTY_T [381,659] : 1.0000
    x EKF2_RNG_SFE [382,660] : 0.0500
    x EKF2_SYNT_MAG_Z [383,666] : 0
    x EKF2_TAS_GATE [384,667] : 3.0000
    x EKF2_TAU_POS [385,668] : 0.2500
    x EKF2_TAU_VEL [386,669] : 0.2500
    x EKF2_TERR_GRAD [387,670] : 0.5000
    x EKF2_TERR_MASK [388,671] : 3
    x EKF2_TERR_NOISE [389,672] : 5.0000
    x EKF2_WIND_NSD [390,673] : 0.0100
    x FD_ACT_EN [391,679] : 1
    x FD_ACT_MOT_C2T [392,680] : 2.0000
    x FD_ACT_MOT_THR [393,681] : 0.2000
    x FD_ACT_MOT_TOUT [394,682] : 100
    x FD_ESCS_EN [395,683] : 1
    x FD_EXT_ATS_EN [396,684] : 0
    x FD_EXT_ATS_TRIG [397,685] : 1900
    x FD_FAIL_P [398,686] : 60
    x FD_FAIL_P_TTRI [399,687] : 0.3000
    x FD_FAIL_R [400,688] : 60
    x FD_FAIL_R_TTRI [401,689] : 0.3000
    x FD_IMB_PROP_THR [402,690] : 30
    x FLW_TGT_ALT_M [403,691] : 0
    x FLW_TGT_DST [404,692] : 8.0000
    x FLW_TGT_FA [405,693] : 180.0000
    x FLW_TGT_HT [406,694] : 8.0000
    x FLW_TGT_MAX_VEL [407,695] : 5.0000
    x FLW_TGT_RS [408,696] : 0.1000
    x FW_AIRSPD_MAX [409,700] : 20.0000
    x FW_AIRSPD_TRIM [410,703] : 15.0000
    x FW_ARSP_MODE [411,704] : 0
    x FW_PSP_OFF [412,754] : 0.0000
    x FW_T_CLMB_R_SP [413,783] : 3.0000
    x FW_T_SINK_R_SP [414,792] : 2.0000
    x GF_ACTION [415,816] : 2
    x GF_ALTMODE [416,817] : 0
    x GF_COUNT [417,818] : -1
    x GF_MAX_HOR_DIST [418,819] : 0.0000
    x + GF_MAX_VER_DIST [419,820] : 30.4800
    x GF_PREDICT [420,821] : 0
    x GF_SOURCE [421,822] : 0
    x GND_SPEED_THR_SC [422,833] : 1.0000
    x GPIO_CTL_CH [423,840] : 0
    x HTE_ACC_GATE [424,870] : 3.0000
    x HTE_HT_ERR_INIT [425,871] : 0.1000
    x HTE_HT_NOISE [426,872] : 0.0036
    x HTE_THR_RANGE [427,873] : 0.2000
    x HTE_VXY_THR [428,874] : 10.0000
    x HTE_VZ_THR [429,875] : 2.0000
    x + IMU_ACCEL_CUTOFF [430,876] : 60.0000
    x + IMU_DGYRO_CUTOFF [431,877] : 40.0000
    x + IMU_GYRO_CUTOFF [432,879] : 80.0000
    x IMU_GYRO_DNF_BW [433,880] : 15.0000
    x + IMU_GYRO_DNF_EN [434,881] : 1
    x IMU_GYRO_DNF_HMC [435,882] : 3
    x IMU_GYRO_DNF_MIN [436,883] : 25.0000
    x IMU_GYRO_NF0_BW [437,889] : 20.0000
    x IMU_GYRO_NF0_FRQ [438,890] : 0.0000
    x IMU_GYRO_NF1_BW [439,891] : 20.0000
    x IMU_GYRO_NF1_FRQ [440,892] : 0.0000
    x + IMU_GYRO_RATEMAX [441,893] : 800
    x IMU_INTEG_RATE [442,894] : 200
    x LNDMC_ALT_GND [443,916] : 2.0000
    x LNDMC_ALT_MAX [444,917] : -1.0000
    x + LNDMC_ROT_MAX [445,918] : 30.0000
    x + LNDMC_TRIG_TIME [446,919] : 0.5000
    x LNDMC_XY_VEL_MAX [447,920] : 1.5000
    x LNDMC_Z_VEL_MAX [448,921] : 0.2500
    x + LND_FLIGHT_T_HI [449,922] : 1
    x + LND_FLIGHT_T_LO [450,923] : 301798580
    x MAN_ARM_GESTURE [451,974] : 1
    x MAV_COMP_ID [452,990] : 1
    x MAV_FWDEXTSP [453,991] : 1
    x MAV_HASH_CHK_EN [454,992] : 1
    x MAV_HB_FORW_EN [455,993] : 1
    x MAV_PROTO_VER [456,994] : 0
    x MAV_RADIO_TOUT [457,995] : 5
    x MAV_SIK_RADIO_ID [458,996] : 0
    x MAV_SYS_ID [459,997] : 1
    x + MAV_TYPE [460,998] : 2
    x MAV_USEHILGPS [461,999] : 0
    x MC_ACRO_EXPO [462,1002] : 0.6900
    x MC_ACRO_EXPO_Y [463,1003] : 0.6900
    x MC_ACRO_P_MAX [464,1004] : 720.0000
    x MC_ACRO_R_MAX [465,1005] : 720.0000
    x MC_ACRO_SUPEXPO [466,1006] : 0.7000
    x MC_ACRO_SUPEXPOY [467,1007] : 0.7000
    x MC_ACRO_Y_MAX [468,1008] : 540.0000
    x MC_AIRMODE [469,1009] : 0
    x MC_AT_APPLY [470,1010] : 1
    x MC_AT_AXES [471,1011] : 3
    x MC_AT_RISE_TIME [472,1013] : 0.1400
    x MC_AT_START [473,1014] : 0
    x MC_AT_SYSID_AMP [474,1015] : 0.7000
    x MC_BAT_SCALE_EN [475,1016] : 0
    x MC_INJECT_AMP [476,1017] : 0.0500
    x MC_INJECT_CNT [477,1018] : 12
    x MC_INJECT_EN [478,1019] : 0
    x MC_INJECT_INC [479,1020] : 1.0000
    x MC_INJECT_REST_T [480,1021] : 1.0000
    x MC_INJECT_RPY [481,1022] : 2
    x MC_INJECT_SINE_T [482,1023] : 5.0000
    x MC_INJECT_START [483,1024] : 3.0000
    x MC_MAN_TILT_TAU [484,1025] : 0.0000
    x MC_ORBIT_RAD_MAX [485,1026] : 1000.0000
    x + MC_PITCHRATE_D [486,1027] : 0.0011
    x MC_PITCHRATE_FF [487,1028] : 0.0000
    x + MC_PITCHRATE_I [488,1029] : 0.0960
    x MC_PITCHRATE_K [489,1030] : 1.0000
    x + MC_PITCHRATE_MAX [490,1031] : 130.0000
    x + MC_PITCHRATE_P [491,1032] : 0.0640
    x + MC_PITCH_CUTOFF [492,1033] : 25.0000
    x + MC_PITCH_P [493,1034] : 8.0000
    x MC_PR_INT_LIM [494,1035] : 0.3000
    x + MC_ROLLRATE_D [495,1036] : 0.0013
    x MC_ROLLRATE_FF [496,1037] : 0.0000
    x + MC_ROLLRATE_I [497,1038] : 0.1000
    x MC_ROLLRATE_K [498,1039] : 1.0000
    x + MC_ROLLRATE_MAX [499,1040] : 130.0000
    x + MC_ROLLRATE_P [500,1041] : 0.0640
    x + MC_ROLL_CUTOFF [501,1042] : 25.0000
    x + MC_ROLL_P [502,1043] : 8.0000
    x MC_RR_INT_LIM [503,1044] : 0.3000
    x MC_THR_CURVE_ACR [504,1045] : 0
    x MC_YAWRATE_D [505,1046] : 0.0000
    x MC_YAWRATE_FF [506,1047] : 0.0000
    x + MC_YAWRATE_I [507,1048] : 0.5000
    x MC_YAWRATE_K [508,1049] : 1.0000
    x + MC_YAWRATE_MAX [509,1050] : 150.0000
    x + MC_YAWRATE_P [510,1051] : 0.0700
    x + MC_YAW_CUTOFF [511,1052] : 15.0000
    x MC_YAW_P [512,1053] : 2.8000
    x MC_YAW_WEIGHT [513,1054] : 0.4000
    x MC_YR_INT_LIM [514,1055] : 0.3000
    x MIS_DIST_1WP [515,1056] : 900.0000
    x MIS_LND_ABRT_ALT [516,1057] : 30
    x MIS_MNT_YAW_CTL [517,1058] : 0
    x MIS_PD_TO [518,1059] : 5.0000
    x + MIS_TAKEOFF_ALT [519,1060] : 0.3048
    x MIS_TKO_LAND_REQ [520,1061] : 0
    x MIS_YAW_ERR [521,1062] : 12.0000
    x MIS_YAW_TMT [522,1063] : -1.0000
    x MODALAI_CONFIG [523,1083] : 0
    x MOT_SLEW_MAX [524,1085] : 0.0000
    x MPC_ACC_DOWN_MAX [525,1086] : 3.0000
    x + MPC_ACC_HOR [526,1087] : 6.0000
    x + MPC_ACC_HOR_MAX [527,1088] : 1000.0000
    x MPC_ACC_UP_MAX [528,1089] : 4.0000
    x MPC_ALT_MODE [529,1090] : 0
    x MPC_HOLD_DZ [530,1091] : 0.1000
    x + MPC_HOLD_MAX_XY [531,1092] : 0.0000
    x + MPC_HOLD_MAX_Z [532,1093] : 0.0000
    x MPC_JERK_AUTO [533,1094] : 4.0000
    x + MPC_JERK_MAX [534,1095] : 40.0000
    x MPC_LAND_ALT1 [535,1096] : 10.0000
    x MPC_LAND_ALT2 [536,1097] : 5.0000
    x MPC_LAND_ALT3 [537,1098] : 1.0000
    x MPC_LAND_CRWL [538,1099] : 0.3000
    x MPC_LAND_RADIUS [539,1100] : 1000.0000
    x MPC_LAND_RC_HELP [540,1101] : 0
    x + MPC_LAND_SPEED [541,1102] : 1.2000
    x + MPC_MANTHR_MIN [542,1103] : 0.0400
    x + MPC_MAN_TILT_MAX [543,1104] : 45.0000
    x MPC_MAN_Y_MAX [544,1105] : 150.0000
    x MPC_MAN_Y_TAU [545,1106] : 0.0800
    x MPC_POS_MODE [546,1107] : 4
    x MPC_THR_CURVE [547,1108] : 0
    x + MPC_THR_HOVER [548,1109] : 0.1200
    x + MPC_THR_MAX [549,1110] : 0.6000
    x + MPC_THR_MIN [550,1111] : 0.0400
    x MPC_THR_XY_MARG [551,1112] : 0.3000
    x MPC_TILTMAX_AIR [552,1113] : 45.0000
    x MPC_TILTMAX_LND [553,1114] : 12.0000
    x + MPC_TKO_RAMP_T [554,1115] : 1.0000
    x MPC_TKO_SPEED [555,1116] : 1.5000
    x MPC_USE_HTE [556,1117] : 1
    x MPC_VELD_LP [557,1118] : 5.0000
    x + MPC_VEL_MANUAL [558,1119] : 20.0000
    x MPC_VEL_MAN_BACK [559,1120] : -1.0000
    x MPC_VEL_MAN_SIDE [560,1121] : -1.0000
    x + MPC_XY_CRUISE [561,1122] : 0.5000
    x MPC_XY_ERR_MAX [562,1123] : 2.0000
    x + MPC_XY_MAN_EXPO [563,1124] : 0.4500
    x MPC_XY_P [564,1125] : 0.9500
    x MPC_XY_TRAJ_P [565,1126] : 0.5000
    x MPC_XY_VEL_ALL [566,1127] : -10.0000
    x MPC_XY_VEL_D_ACC [567,1128] : 0.2000
    x MPC_XY_VEL_I_ACC [568,1129] : 0.4000
    x + MPC_XY_VEL_MAX [569,1130] : 20.0000
    x MPC_XY_VEL_P_ACC [570,1131] : 1.8000
    x MPC_YAWRAUTO_MAX [571,1132] : 45.0000
    x + MPC_YAW_EXPO [572,1133] : 0.3000
    x MPC_YAW_MODE [573,1134] : 0
    x + MPC_Z_MAN_EXPO [574,1135] : 0.1000
    x + MPC_Z_P [575,1136] : 5.0000
    x MPC_Z_VEL_ALL [576,1137] : -3.0000
    x MPC_Z_VEL_D_ACC [577,1138] : 0.0000
    x MPC_Z_VEL_I_ACC [578,1139] : 2.0000
    x + MPC_Z_VEL_MAX_DN [579,1140] : 4.0000
    x + MPC_Z_VEL_MAX_UP [580,1141] : 10.0000
    x + MPC_Z_VEL_P_ACC [581,1142] : 8.0000
    x + MPC_Z_V_AUTO_DN [582,1143] : 3.0000
    x + MPC_Z_V_AUTO_UP [583,1144] : 10.0000
    x NAV_ACC_RAD [584,1148] : 10.0000
    x NAV_DLL_ACT [585,1149] : 0
    x NAV_FORCE_VT [586,1150] : 1
    x NAV_FW_ALTL_RAD [587,1151] : 5.0000
    x NAV_FW_ALT_RAD [588,1152] : 10.0000
    x NAV_LOITER_RAD [589,1153] : 80.0000
    x NAV_MC_ALT_RAD [590,1154] : 0.8000
    x NAV_MIN_LTR_ALT [591,1155] : -1.0000
    x NAV_RCL_ACT [592,1156] : 2
    x NAV_TRAFF_AVOID [593,1157] : 1
    x NAV_TRAFF_A_HOR [594,1158] : 500.0000
    x NAV_TRAFF_A_VER [595,1159] : 500.0000
    x NAV_TRAFF_COLL_T [596,1160] : 60
    x PLD_BTOUT [597,1215] : 5.0000
    x PLD_FAPPR_ALT [598,1216] : 0.1000
    x PLD_HACC_RAD [599,1217] : 0.2000
    x PLD_MAX_SRCH [600,1218] : 3
    x PLD_SRCH_ALT [601,1219] : 10.0000
    x PLD_SRCH_TOUT [602,1220] : 10.0000
    x RC10_DZ [603,1267] : 0.0000
    x RC10_MAX [604,1268] : 2000.0000
    x RC10_MIN [605,1269] : 1000.0000
    x RC10_REV [606,1270] : 1.0000
    x RC10_TRIM [607,1271] : 1500.0000
    x RC11_DZ [608,1272] : 0.0000
    x RC11_MAX [609,1273] : 2000.0000
    x RC11_MIN [610,1274] : 1000.0000
    x RC11_REV [611,1275] : 1.0000
    x RC11_TRIM [612,1276] : 1500.0000
    x RC12_DZ [613,1277] : 0.0000
    x RC12_MAX [614,1278] : 2000.0000
    x RC12_MIN [615,1279] : 1000.0000
    x RC12_REV [616,1280] : 1.0000
    x RC12_TRIM [617,1281] : 1500.0000
    x RC13_DZ [618,1282] : 0.0000
    x RC13_MAX [619,1283] : 2000.0000
    x RC13_MIN [620,1284] : 1000.0000
    x RC13_REV [621,1285] : 1.0000
    x RC13_TRIM [622,1286] : 1500.0000
    x RC14_DZ [623,1287] : 0.0000
    x RC14_MAX [624,1288] : 2000.0000
    x RC14_MIN [625,1289] : 1000.0000
    x RC14_REV [626,1290] : 1.0000
    x RC14_TRIM [627,1291] : 1500.0000
    x RC15_DZ [628,1292] : 0.0000
    x RC15_MAX [629,1293] : 2000.0000
    x RC15_MIN [630,1294] : 1000.0000
    x RC15_REV [631,1295] : 1.0000
    x RC15_TRIM [632,1296] : 1500.0000
    x RC16_DZ [633,1297] : 0.0000
    x RC16_MAX [634,1298] : 2000.0000
    x RC16_MIN [635,1299] : 1000.0000
    x RC16_REV [636,1300] : 1.0000
    x RC16_TRIM [637,1301] : 1500.0000
    x RC17_DZ [638,1302] : 0.0000
    x RC17_MAX [639,1303] : 2000.0000
    x RC17_MIN [640,1304] : 1000.0000
    x RC17_REV [641,1305] : 1.0000
    x RC17_TRIM [642,1306] : 1500.0000
    x RC18_DZ [643,1307] : 0.0000
    x RC18_MAX [644,1308] : 2000.0000
    x RC18_MIN [645,1309] : 1000.0000
    x RC18_REV [646,1310] : 1.0000
    x RC18_TRIM [647,1311] : 1500.0000
    x RC1_DZ [648,1312] : 10.0000
    x RC1_MAX [649,1313] : 2000.0000
    x RC1_MIN [650,1314] : 1000.0000
    x RC1_REV [651,1315] : 1.0000
    x RC1_TRIM [652,1316] : 1500.0000
    x RC2_DZ [653,1317] : 10.0000
    x RC2_MAX [654,1318] : 2000.0000
    x RC2_MIN [655,1319] : 1000.0000
    x RC2_REV [656,1320] : 1.0000
    x RC2_TRIM [657,1321] : 1500.0000
    x RC3_DZ [658,1322] : 10.0000
    x RC3_MAX [659,1323] : 2000.0000
    x RC3_MIN [660,1324] : 1000.0000
    x RC3_REV [661,1325] : 1.0000
    x RC3_TRIM [662,1326] : 1500.0000
    x RC4_DZ [663,1327] : 10.0000
    x RC4_MAX [664,1328] : 2000.0000
    x RC4_MIN [665,1329] : 1000.0000
    x RC4_REV [666,1330] : 1.0000
    x RC4_TRIM [667,1331] : 1500.0000
    x RC5_DZ [668,1332] : 10.0000
    x + RC5_MAX [669,1333] : 1980.0000
    x + RC5_MIN [670,1334] : 1030.0000
    x RC5_REV [671,1335] : 1.0000
    x + RC5_TRIM [672,1336] : 1505.0000
    x RC6_DZ [673,1337] : 10.0000
    x + RC6_MAX [674,1338] : 1980.0000
    x + RC6_MIN [675,1339] : 1030.0000
    x RC6_REV [676,1340] : 1.0000
    x + RC6_TRIM [677,1341] : 1505.0000
    x RC7_DZ [678,1342] : 10.0000
    x + RC7_MAX [679,1343] : 1980.0000
    x + RC7_MIN [680,1344] : 1030.0000
    x RC7_REV [681,1345] : 1.0000
    x + RC7_TRIM [682,1346] : 1505.0000
    x RC8_DZ [683,1347] : 10.0000
    x + RC8_MAX [684,1348] : 1980.0000
    x + RC8_MIN [685,1349] : 1030.0000
    x RC8_REV [686,1350] : 1.0000
    x + RC8_TRIM [687,1351] : 1505.0000
    x RC9_DZ [688,1352] : 0.0000
    x RC9_MAX [689,1353] : 2000.0000
    x RC9_MIN [690,1354] : 1000.0000
    x RC9_REV [691,1355] : 1.0000
    x RC9_TRIM [692,1356] : 1500.0000
    x RC_ARMSWITCH_TH [693,1357] : 0.7500
    x + RC_CHAN_CNT [694,1358] : 16
    x RC_ENG_MOT_TH [695,1360] : 0.7500
    x RC_FAILS_THR [696,1361] : 0
    x RC_GEAR_TH [697,1362] : 0.7500
    x RC_KILLSWITCH_TH [698,1364] : 0.7500
    x RC_LOITER_TH [699,1365] : 0.7500
    x RC_MAP_ACRO_SW [700,1366] : 0
    x RC_MAP_ARM_SW [701,1367] : 0
    x RC_MAP_AUX1 [702,1368] : 0
    x RC_MAP_AUX2 [703,1369] : 0
    x RC_MAP_AUX3 [704,1370] : 0
    x RC_MAP_AUX4 [705,1371] : 0
    x RC_MAP_AUX5 [706,1372] : 0
    x RC_MAP_AUX6 [707,1373] : 0
    x RC_MAP_ENG_MOT [708,1374] : 0
    x RC_MAP_FAILSAFE [709,1375] : 0
    x RC_MAP_FLAPS [710,1376] : 0
    x + RC_MAP_FLTMODE [711,1377] : 6
    x RC_MAP_FLTM_BTN [712,1378] : 0
    x RC_MAP_GEAR_SW [713,1379] : 0
    x + RC_MAP_KILL_SW [714,1380] : 5
    x RC_MAP_LOITER_SW [715,1381] : 0
    x RC_MAP_MAN_SW [716,1382] : 0
    x RC_MAP_MODE_SW [717,1383] : 0
    x RC_MAP_OFFB_SW [718,1384] : 0
    x RC_MAP_PARAM1 [719,1385] : 0
    x RC_MAP_PARAM2 [720,1386] : 0
    x RC_MAP_PARAM3 [721,1387] : 0
    x + RC_MAP_PITCH [722,1388] : 2
    x RC_MAP_POSCTL_SW [723,1389] : 0
    x RC_MAP_RATT_SW [724,1390] : 0
    x RC_MAP_RETURN_SW [725,1391] : 0
    x + RC_MAP_ROLL [726,1392] : 1
    x RC_MAP_STAB_SW [727,1393] : 0
    x + RC_MAP_THROTTLE [728,1394] : 3
    x RC_MAP_TRANS_SW [729,1395] : 0
    x + RC_MAP_YAW [730,1396] : 4
    x RC_OFFB_TH [731,1397] : 0.7500
    x RC_RETURN_TH [732,1398] : 0.7500
    x RC_TRANS_TH [733,1402] : 0.7500
    x RTL_CONE_ANG [734,1403] : 45
    x RTL_DESCEND_ALT [735,1404] : 30.0000
    x RTL_HDG_MD [736,1405] : 0
    x RTL_LAND_DELAY [737,1406] : 0.0000
    x RTL_LOITER_RAD [738,1407] : 80.0000
    x RTL_MIN_DIST [739,1408] : 10.0000
    x RTL_PLD_MD [740,1409] : 0
    x RTL_RETURN_ALT [741,1410] : 60.0000
    x RTL_TIME_FACTOR [742,1411] : 1.1000
    x RTL_TIME_MARGIN [743,1412] : 100
    x RTL_TYPE [744,1413] : 0
    x SDLOG_BOOT_BAT [745,1424] : 0
    x SDLOG_DIRS_MAX [746,1425] : 0
    x SDLOG_MISSION [747,1428] : 0
    x SDLOG_MODE [748,1429] : 0
    x + SDLOG_PROFILE [749,1430] : 129
    x SDLOG_UTC_OFFSET [750,1431] : 0
    x SDLOG_UUID [751,1432] : 1
    x SENS_BARO_QNH [752,1434] : 1013.2500
    x SENS_BARO_RATE [753,1435] : 20.0000
    x SENS_BOARD_ROT [754,1436] : 0
    x + SENS_BOARD_X_OFF [755,1437] : 1.3898
    x + SENS_BOARD_Y_OFF [756,1438] : -1.4985
    x SENS_BOARD_Z_OFF [757,1439] : 0.0000
    x SENS_DPRES_OFF [758,1442] : 0.0000
    x SENS_IMU_AUTOCAL [759,1487] : 0
    x SENS_IMU_MODE [760,1488] : 1
    x SYS_AUTOCONFIG [761,1645] : 0
    x + SYS_AUTOSTART [762,1646] : 4001
    x SYS_CAL_TDEL [763,1651] : 24
    x SYS_CAL_TMAX [764,1652] : 10
    x SYS_CAL_TMIN [765,1653] : 5
    x SYS_FAC_CAL_MODE [766,1655] : 0
    x SYS_FAILURE_EN [767,1656] : 0
    x SYS_HAS_BARO [768,1657] : 1
    x + SYS_HAS_GPS [769,1658] : 0
    x + SYS_HAS_MAG [770,1659] : 0
    x SYS_HAS_NUM_DIST [771,1660] : 0
    x SYS_HITL [772,1661] : 0
    x SYS_MC_EST_GROUP [773,1662] : 2
    x SYS_RGB_MAXBRT [774,1663] : 1.0000
    x SYS_STCK_EN [775,1664] : 1
    x SYS_VEHICLE_RESP [776,1666] : -0.4000
    x + THR_MDL_FAC [777,1866] : 0.9000
    x TRIG_MODE [778,1872] : 0
    x UAVCAN_ENABLE [779,1913] : 0
    x + VOXL_ESC_BAUD [780,2095] : 2000000
    x + VOXL_ESC_CONFIG [781,2096] : 1
    x + VOXL_ESC_FUNC1 [782,2097] : 102
    x + VOXL_ESC_FUNC2 [783,2098] : 103
    x + VOXL_ESC_FUNC3 [784,2099] : 101
    x + VOXL_ESC_FUNC4 [785,2100] : 104
    x VOXL_ESC_MODE [786,2101] : 0
    x VOXL_ESC_PUB_BST [787,2102] : 1
    x VOXL_ESC_REV [788,2103] : 0
    x + VOXL_ESC_RPM_MAX [789,2104] : 12000
    x + VOXL_ESC_RPM_MIN [790,2105] : 2000
    x VOXL_ESC_SDIR1 [791,2106] : 0
    x VOXL_ESC_SDIR2 [792,2107] : 0
    x VOXL_ESC_SDIR3 [793,2108] : 0
    x VOXL_ESC_SDIR4 [794,2109] : 0
    x VOXL_ESC_T_COSP [795,2110] : 0.9900
    x VOXL_ESC_T_DEAD [796,2111] : 20
    x VOXL_ESC_T_EXPO [797,2112] : 35
    x VOXL_ESC_T_MINF [798,2113] : 0.1500
    x VOXL_ESC_T_OVER [799,2114] : 0
    x VOXL_ESC_T_PERC [800,2115] : 90
    x VOXL_ESC_T_WARN [801,2116] : 0
    x + VOXL_ESC_VLOG [802,2117] : 1
    x VTO_LOITER_ALT [803,2118] : 80.0000
    x VT_B_DEC_MSS [804,2123] : 2.0000
    x WV_EN [805,2156] : 0
    x WV_GAIN [806,2157] : 1.0000
    x WV_ROLL_MIN [807,2158] : 1.0000
    x WV_YRATE_MAX [808,2159] : 90.0000
    x XRCE_DDS_DOM_ID [809,2160] : 0
    x XRCE_DDS_KEY [810,2161] : 1

    811/2162 parameters used.

    Could you kindly assist me in resolving this issue? Any guidance or recommendations would be greatly appreciated.

    Thank you for your support!

    Ask your questions right here!

  • Starling 2 Max Drone drifting off
    V vamsi

    @Moderator Thank you for the response; I was going through the https://www.youtube.com/watch?v=Cpbbye3Z6co in that the drone does not have any drift in the manual mode, so I thought I might have missed any configuration changes.

    When I changed my mode to "indoor_vio_missing_gps.params" and when I controlled it with the Remote Controller, I was able to fly it in the position mode, and when I changed it to Off-board mode on RC, it did the figure 8.

    The Drone still drifts off when I run the below code in the Position mode

    #!/usr/bin/env python3

    """
    Caveat when attempting to run the examples in non-gps environments:

    drone.offboard.stop() will return a COMMAND_DENIED result because it
    requires a mode switch to HOLD, something that is currently not supported in a
    non-gps environment.
    """

    import asyncio

    from mavsdk import System
    from mavsdk.offboard import (OffboardError, PositionNedYaw)

    async def run():
    """ Does Offboard control using position NED coordinates. """

    drone = System()
    print("Connecting to vehicle using port 14550")
    await drone.connect(system_address="udp://:14550")
    
    print("Waiting for drone to connect...")
    async for state in drone.core.connection_state():
        if state.is_connected:
            print(f"-- Connected to drone!")
            break
    
    
    
    print("-- Arming")
    await drone.action.arm()
    
    max_speed = await drone.action.get_maximum_speed()
    
    
    print(f"Maximum speed: {max_speed} m/s")
    
    await drone.action.set_maximum_speed(0.5)
    await asyncio.sleep(4)
    
    max_speed = await drone.action.get_maximum_speed()
    
    await asyncio.sleep(5)
    
    print("-- Setting initial setpoint")
    await drone.offboard.set_position_ned(PositionNedYaw(0.0, 0.0, 0.0, 0.0))
    
    
    
    
    print("-- Starting offboard")
    try:
        await drone.offboard.start()
    except OffboardError as error:
        print(f"Starting offboard mode failed \
                with error code: {error._result.result}")
        print("-- Disarming")
        await drone.action.disarm()
        return
    
    await asyncio.sleep(5)
    
    print("-- Go 0m North, 0m East, -0.20m Down \
            within local coordinate system")
    await drone.offboard.set_position_ned(
            PositionNedYaw(0.0, 0.0, -0.20, 0.0))
    await asyncio.sleep(3)
    
    #print("-- Go 0m North, 0m East, 0m Down within local coordinate system")
    #await drone.offboard.set_position_ned(PositionNedYaw(0.0, 0.0, 0.0, 0.0)
    #await asyncio.sleep(5)
    
    print("Trying to land")
    try:
        await drone.action.land()
    except:
        print("Failed to land")
    
    print("-- Disarming")
    try:
        await drone.action.disarm()
    except:
        print("Disarming failed")
    

    if name == "main":
    # Run the asyncio loop
    asyncio.run(run())

    I ran the above code and after taking off the drone again drifted off

    here are the attached videos

    Flight video

    Questions:

    1. Is there a configuration or calibration step I may have missed to prevent drifting?
    2. Does the script require any additional commands for better stability ?
    3. Could this be related to parameter tuning or sensor limitations in a non-GPS environment?
      Thank you for your assistance!
    Ask your questions right here!

  • Starling 2 Max Drone drifting off
    V vamsi

    Hi Team,

    I am using Starling 2 max, and I was trying to fly the drone in manual mode using the remote controller to do initial basic checks before using Mavsdk to fly the drone.

    When I try to fly the drone, it drifts toward the left instead of vertical take-off.

    I tried to run
    systemctl stop voxl-px4
    ./voxl-esc-spin.py --id 255 --power 60 --ramp-time 3.0 --timeout 4.0 --enable-plot 1 without having any propellers and screws to check if there is any rpm difference in the motors the below are the results

    ed4c6afe-a3ba-411d-9d36-37984d33b0c9-image.png

    c449f4c1-6f30-4d43-a75d-03f7bf563e36-image.png

    43233ca2-fcc0-488a-a9f5-105474c47f75-image.png

    d84f8bcd-bde9-4d0d-86e5-6b1ac1ce2fdd-image.png

    3e8c5536-34e0-4a5e-9ba2-032af504e9a6-image.png

    416fd223-4910-429d-911d-6545731ad5cc-image.png
    ead90dbb-5974-422a-9ab2-642dde6c8fc3-image.png

    9f98fc36-77c0-4a28-b7b8-a8d6827eb428-image.png

    I am unsure if the deviation of 264.00 rpm is causing this issue.

    please find the attached px4 logs -> https://review.px4.io/plot_app?log=23827d44-827c-4f54-897c-b0ccac53c96a

    Can you please help me with this issue?

    Ask your questions right here!

  • Battery Charger for Starling 2 Max
    V vamsi

    @Zachary-Lowell-0 Thank you for letting me know. this is my first time working with a multi-cell battery and a smart charger. I will be careful not to connect multiple batteries at the same time.

    Support Request Format for Best Results

  • Battery Charger for Starling 2 Max
    V vamsi

    @tom Thank you for the response I now know what the issue is I will just connect a single battery, use 2s in the settings, and use an XT30 to XT60 converter to connect my XT30 to the "Battery" on the charger.

    Support Request Format for Best Results

  • Battery Charger for Starling 2 Max
    V vamsi

    HI Team,

    I have purchased the recommended charger for the Starling 2 max -> https://www.amazon.com/ISDT-Q6-Nano-Charger-Discharger/dp/B09VRVPHW8/, and when I try to change my battery, it shows the operation is not supported. I am attaching the images for the reference. can you please help me with this issue

    WhatsApp Image 2024-11-04 at 14.12.20 (1).jpeg
    The above are my connections.

    I tried to start the charge task with the below settings
    WhatsApp Image 2024-11-04 at 14.12.20.jpeg

    But I am getting this issue
    WhatsApp Image 2024-11-04 at 14.12.11.jpeg

    Support Request Format for Best Results
  • Login

  • Don't have an account? Register

  • Login or register to search.
  • First post
    Last post
0
  • Categories
  • Recent
  • Tags
  • Popular
  • Users
  • Groups