I2C reading of 12S battery

[Nikos Mavr]

@Eric-Katzfey Yes, that worked, identified bus 4 channel 41. No while INA228 is enabled, I am not sure whether I should change the power_manager in voxl-px4.conf to NONE or EXTERNAL.

[Nikos Mavr]

@Vinny !

[Vinny]

Thanks @Nikos-Mavr for the drawing, that helped.
The thing to be careful about is the I2C voltage levels.
https://docs.modalai.com/voxl2-connectors/

J19 port I2C's are set to 3.3V with on-board pullups. So, I'm not sure what the 12S module I2C levels are, but be sure they are either (3.3V) or (set by host, i.e.: no pulls on the battery side)

I'm not sure what voltage is feeding into this portion... make sure it is limited to 6S:

Now that Eric has given you a bunch of guidance, let us know if there are still problems overall.

Thanks!

[Eric Katzfey]

@Nikos-Mavr Okay, great, so the I2C is working then. But address 0x41 is an INA226, not an INA228. The PX4 driver indicates that an INA228 has an address of 0x45. And the Holybro data sheet for the PM02D indicates that the lower voltage one for up to 6S battery uses the INA226 while the higher voltage one for up to 12S. Am I reading that correctly? Regardless, it doesn't matter how you set POWER_MANAGER in voxl-px4.conf because that just determines whether it will start the voxlpm driver. But, probably best to set it to EXTERNAL for now. The bigger issue is that the drivers for INA226 and INA228 are not in the image. So they need to be added to the image and then started in the voxl-px4-start startup script located in /usr/bin.

[Eric Katzfey]

@Nikos-Mavr I added the ina226 and ina228 drivers into the build. Updated build can be found here: http://voxl-packages.modalai.com/dists/qrb5165/dev/binary-arm64/voxl-px4_1.14.0-2.0.136-202603180951_arm64.deb

To try it out use the command qshell ina226 start -X -b 4 or qshell ina228 start -X -b 4 from the px4 command line to see if the driver sees your device.

[Nikos Mavr]

@Vinny yes I removed the level shifter for that setup and yes the voltage drops to 3s for the highlighted area.

[Nikos Mavr]

@Eric-Katzfey
Thank you for your constant help. Unfortunately, this is what I get with this package with both command and even when I am trying to scan i2c now.
pxh> qshell ina226 start -X -b 4
INFO [qshell] Send cmd: 'ina226 start -X -b 4'
ERROR [uORB] Error Sending [qshell_req] topic data over comm_channel
ERROR [qshell] command timed out
ERROR [qshell] Command failed

[Eric Katzfey]

@Nikos-Mavr Can you reboot, try the command again, and send the entire output of PX4 so that I can see the entire startup process?

[Nikos Mavr]

@Eric-Katzfey

[Nikos Mavr]

@Eric-Katzfey upgraded to latest SDK now it is smooth
pxh> qshell ina226 start -X -b 4
INFO [qshell] Send cmd: 'ina226 start -X -b 4'
INFO [muorb] [uORB] Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO [muorb] [qshell] qshell gotten: ina226 start -X -b 4
INFO [muorb] [qshell] arg0 = 'ina226'
INFO [muorb] [qshell] arg1 = 'start'
INFO [muorb] [qshell] arg2 = '-X'
INFO [muorb] [qshell] arg3 = '-b'
INFO [muorb] [qshell] arg4 = '4'
INFO [muorb] [drivers__device] *** I2C Device ID 0xd04121 13648161
INFO [uORB] Marking DeviceNode(battery_status) as advertised in process_remote_topic
INFO [muorb] [drivers__device] Set up I2C bus mutex for bus 4
INFO [muorb] ina226 #0 on I2C bus 4
INFO [muorb] (external)
INFO [muorb] address 0x41
INFO [muorb]

INFO [muorb] [qshell] Ok executing command: ina226 start -X -b 4
INFO [qshell] qshell return value timestamp: 1170693307, local time: 1170694295

[Nikos Mavr]

@Nikos-Mavr Oh wow, it works now. Thank you for your help. By the way during this process my tp link antenna stopped responding and when I do voxl-wifi it says wifi devices not detected, while the device works for other PCS and voxl recognizes other USB devices. Are there any ideas why?

[Eric Katzfey]

@Nikos-Mavr You're welcome! And can you please start a new forum post for this new issue? Thanks!