VOXL2 Wifi+Doodle
-
Hi,
I'm using the VOXL2 with the VOXL 2 Ethernet and USB Hub Add-on board, and I have wifi on the USB3 port (J11), a doodle radio on the USB2 port (J12), and keep the ethernet port open for hardwiring with an ethernet cable (J13). My problem is when I use the voxl-configure-modem command to set the static ip for the doodle, I cannot ping it. It works just fine using the USB3 UART Add-On, and I think this is because that board only exposes eth0. However, the Ethernet and USB Hub Add-on board has both eth0 and eth1. If I run
ip addr add 10.223.1.101/16 dev eth1, I am able to ping the doodle and it works just fine.My question is what is the intended method (if any) to essentially run voxl-configure-modem such that it configures everything for eth1 instead of eth0? If there is no way to do that, how would you recommend I persist a static ip on eth1 though reboots?
-
Hi,
I'm using the VOXL2 with the VOXL 2 Ethernet and USB Hub Add-on board, and I have wifi on the USB3 port (J11), a doodle radio on the USB2 port (J12), and keep the ethernet port open for hardwiring with an ethernet cable (J13). My problem is when I use the voxl-configure-modem command to set the static ip for the doodle, I cannot ping it. It works just fine using the USB3 UART Add-On, and I think this is because that board only exposes eth0. However, the Ethernet and USB Hub Add-on board has both eth0 and eth1. If I run
ip addr add 10.223.1.101/16 dev eth1, I am able to ping the doodle and it works just fine.My question is what is the intended method (if any) to essentially run voxl-configure-modem such that it configures everything for eth1 instead of eth0? If there is no way to do that, how would you recommend I persist a static ip on eth1 though reboots?
@ctitus The
voxl-modem-startscript which gets run on boot after runningvoxl-configure-modemis hard-coded toeth0but it is just a simple bash script that you can modify if you'd like to fit your use-case.The script itself lives at
/usr/bin/voxl-modem-startThis is the area you would want to modify:
scripts/voxl-modem-start · master · voxl / VOXL SDK / Utilities / voxl-modem · GitLab
Modem utilities for the VOXL platform.
GitLab (gitlab.com)
-
Hi,
I'm using the VOXL2 with the VOXL 2 Ethernet and USB Hub Add-on board, and I have wifi on the USB3 port (J11), a doodle radio on the USB2 port (J12), and keep the ethernet port open for hardwiring with an ethernet cable (J13). My problem is when I use the voxl-configure-modem command to set the static ip for the doodle, I cannot ping it. It works just fine using the USB3 UART Add-On, and I think this is because that board only exposes eth0. However, the Ethernet and USB Hub Add-on board has both eth0 and eth1. If I run
ip addr add 10.223.1.101/16 dev eth1, I am able to ping the doodle and it works just fine.My question is what is the intended method (if any) to essentially run voxl-configure-modem such that it configures everything for eth1 instead of eth0? If there is no way to do that, how would you recommend I persist a static ip on eth1 though reboots?
Hi @ctitus
M0062 USB2 ports are not current-capable of powering a Doodle Radio at full specs. They are only 1A.
https://docs.modalai.com/m0062/#detailsDoodle requires 2A support, which can only come from our 10-pin format USB ports on M0130.
This table does not include M0062 since it was never intended to be a production product (so I need to update that table):
https://docs.modalai.com/expansion-design-guide/#usb-expansion-over-j3--j5You should certainly get basic stuff working, but you will not achieve Doodle published ranges and output powers on any board we have other than M0130 or M0078: https://docs.modalai.com/usb-epxansion-with-fastboot-v2-datasheet/
-
Hi @ctitus
M0062 USB2 ports are not current-capable of powering a Doodle Radio at full specs. They are only 1A.
https://docs.modalai.com/m0062/#detailsDoodle requires 2A support, which can only come from our 10-pin format USB ports on M0130.
This table does not include M0062 since it was never intended to be a production product (so I need to update that table):
https://docs.modalai.com/expansion-design-guide/#usb-expansion-over-j3--j5You should certainly get basic stuff working, but you will not achieve Doodle published ranges and output powers on any board we have other than M0130 or M0078: https://docs.modalai.com/usb-epxansion-with-fastboot-v2-datasheet/
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login