doodle labs and joystick setup
-
Hey @Alex-Kushleyev @Eric-Katzfey @Chad-Sweet
I had a query about setting up joystick with doodle labs. I am not able to setup the joystick properly, not every buttons and toggle is working. AUX channels for Turtle mode or toggle for changing modes.my setup is
- voxl 2 to Fc v2 to ESC
- doodle labs nano to voxl 2
@Jetson-Nano Are you using QGC to map joystick buttons to functions? What version of PX4 are you running on your FC v2?
-
@Jetson-Nano Are you using QGC to map joystick buttons to functions? What version of PX4 are you running on your FC v2?
@Eric-Katzfey For turtle mode with a joystick you need to set VOXL_ESC_MODE to 1 and, while not armed, press a button and keep it pressed while arming. For flight modes that should all be handled through QGC.
-
@Jetson-Nano Are you using QGC to map joystick buttons to functions? What version of PX4 are you running on your FC v2?
@Eric-Katzfey yes , I am using the QGC to map joystick buttons. I am using the voxl-fpv-dev version from the modalai px4 repo. I am using the FPV 4-in-1 ESC. I am not able to get more than 2 toggle switches and also not able to assign them two way.
-
@Eric-Katzfey yes , I am using the QGC to map joystick buttons. I am using the voxl-fpv-dev version from the modalai px4 repo. I am using the FPV 4-in-1 ESC. I am not able to get more than 2 toggle switches and also not able to assign them two way.
@Jetson-Nano
voxl-fpv-devis the name of the branch. The version will be a number, such as1.14.0-8.104.3. Most of the joystick button mapping is handled by QGC directly. It maps them to commands that are sent over Mavlink. But the turtle mode is something specific built into the ESC driver. For the joystick buttons to work for turtle mode you need to set VOXL_ESC_MODE to 1. For newer versions of thevoxl-fpv-devbranch you can also set VOXL_ESC_MODE to 2. The verify that the button mapping is working you can look at the manual_control_setpoint topic in px4 and see if the aux1 / aux2 fields are changing between 0.0 and 1.0. (e.g.px4-listener manual_control_setpoint) -
@Jetson-Nano
voxl-fpv-devis the name of the branch. The version will be a number, such as1.14.0-8.104.3. Most of the joystick button mapping is handled by QGC directly. It maps them to commands that are sent over Mavlink. But the turtle mode is something specific built into the ESC driver. For the joystick buttons to work for turtle mode you need to set VOXL_ESC_MODE to 1. For newer versions of thevoxl-fpv-devbranch you can also set VOXL_ESC_MODE to 2. The verify that the button mapping is working you can look at the manual_control_setpoint topic in px4 and see if the aux1 / aux2 fields are changing between 0.0 and 1.0. (e.g.px4-listener manual_control_setpoint)@Eric-Katzfey Thank you for the support. I will test it out and get back to you encase of any further queries.
-
@Eric-Katzfey Thank you for the support. I will test it out and get back to you encase of any further queries.
@Eric-Katzfey
I tested what you asked me, since i am using external Fc and doodle labs, I am not able to assign AUX to any button, is there any work around on how to assign AUX -
@Eric-Katzfey
I tested what you asked me, since i am using external Fc and doodle labs, I am not able to assign AUX to any button, is there any work around on how to assign AUX@Eric-Katzfey @Alex-Kushleyev
hey guys, just a random thought, can I enable turtle mode through a button instead of taking AUX 1 into consideration. just a thought, any guidance and help would be greatly appreciated. -
@Eric-Katzfey @Alex-Kushleyev
hey guys, just a random thought, can I enable turtle mode through a button instead of taking AUX 1 into consideration. just a thought, any guidance and help would be greatly appreciated.@Jetson-Nano What do you see if you go to the MAVLink console in QGC and look at the manual_control_setpoint topic? (
listener manual_control_setpoint)? -
@Jetson-Nano What do you see if you go to the MAVLink console in QGC and look at the manual_control_setpoint topic? (
listener manual_control_setpoint)?@Eric-Katzfey Also, there is a parameter called VOXL_ESC_T_ON. How is that set? It determines which button will be used for turtle mode. The code is here: https://github.com/modalai/px4-firmware/blob/ea098200d3c09b7af548bf7be29fda245fad8f17/src/modules/mavlink/mavlink_receiver.cpp#L2083
-
@Jetson-Nano What do you see if you go to the MAVLink console in QGC and look at the manual_control_setpoint topic? (
listener manual_control_setpoint)?@Eric-Katzfey
This is the output i am getting while runninglistener manual_control_setpointNuttShell (NSH) NuttX-11.0.0 nsh> listener manual_control_setpoint TOPIC: manual_control_setpoint manual_control_setpoint timestamp: 438754659 (0.033455 seconds ago) timestamp_sample: 438754653 (6 us before timestamp) roll: 0.00000 pitch: 0.00000 yaw: 0.00000 throttle: 0.00000 flaps: 0.00000 aux1: 0.00000 aux2: 0.00000 aux3: 0.00000 aux4: 0.00000 aux5: 0.00000 aux6: 0.00000 buttons: 0 valid: True data_source: 2 sticks_moving: False nsh> listener manual_control_setpoint TOPIC: manual_control_setpoint manual_control_setpoint timestamp: 446282690 (0.039850 seconds ago) timestamp_sample: 446282683 (7 us before timestamp) roll: 0.00000 pitch: 0.00000 yaw: 0.00000 throttle: 0.00000 flaps: 0.00000 aux1: 0.00000 aux2: 0.00000 aux3: 0.00000 aux4: 0.00000 aux5: 0.00000 aux6: 0.00000 buttons: 0 valid: True data_source: 2 sticks_moving: False -
@Eric-Katzfey Also, there is a parameter called VOXL_ESC_T_ON. How is that set? It determines which button will be used for turtle mode. The code is here: https://github.com/modalai/px4-firmware/blob/ea098200d3c09b7af548bf7be29fda245fad8f17/src/modules/mavlink/mavlink_receiver.cpp#L2083
@Eric-Katzfey I am not able to see the option you have mentioned
VOXL_ESC_T_ON -
@Eric-Katzfey I am not able to see the option you have mentioned
VOXL_ESC_T_ON@Jetson-Nano said in doodle labs and joystick setup:
I am not able to see the option you have mentioned VOXL_ESC_T_ON
In the Mavlink console what do you see with "param show VOXL_ESC_*"?
And what about "ver all"?
-
@Eric-Katzfey
This is the output i am getting while runninglistener manual_control_setpointNuttShell (NSH) NuttX-11.0.0 nsh> listener manual_control_setpoint TOPIC: manual_control_setpoint manual_control_setpoint timestamp: 438754659 (0.033455 seconds ago) timestamp_sample: 438754653 (6 us before timestamp) roll: 0.00000 pitch: 0.00000 yaw: 0.00000 throttle: 0.00000 flaps: 0.00000 aux1: 0.00000 aux2: 0.00000 aux3: 0.00000 aux4: 0.00000 aux5: 0.00000 aux6: 0.00000 buttons: 0 valid: True data_source: 2 sticks_moving: False nsh> listener manual_control_setpoint TOPIC: manual_control_setpoint manual_control_setpoint timestamp: 446282690 (0.039850 seconds ago) timestamp_sample: 446282683 (7 us before timestamp) roll: 0.00000 pitch: 0.00000 yaw: 0.00000 throttle: 0.00000 flaps: 0.00000 aux1: 0.00000 aux2: 0.00000 aux3: 0.00000 aux4: 0.00000 aux5: 0.00000 aux6: 0.00000 buttons: 0 valid: True data_source: 2 sticks_moving: False@Jetson-Nano said in doodle labs and joystick setup:
This is the output i am getting while running listener manual_control_setpoint
What is the parameter COM_RC_IN_MODE set to?
-
@Jetson-Nano said in doodle labs and joystick setup:
This is the output i am getting while running listener manual_control_setpoint
What is the parameter COM_RC_IN_MODE set to?
@Eric-Katzfey COM_RC_IN_MODE is set to joystick only
-
@Eric-Katzfey Also, there is a parameter called VOXL_ESC_T_ON. How is that set? It determines which button will be used for turtle mode. The code is here: https://github.com/modalai/px4-firmware/blob/ea098200d3c09b7af548bf7be29fda245fad8f17/src/modules/mavlink/mavlink_receiver.cpp#L2083
@Eric-Katzfey Hey hope you are doing fine, I checked the code and various branches of PX4, I noticed I was able to see the parameter
VOXL_ESC_T_ONbut the option only showcased button 1 for assignment . what to do if I want to assign another button. -
@Eric-Katzfey Hey hope you are doing fine, I checked the code and various branches of PX4, I noticed I was able to see the parameter
VOXL_ESC_T_ONbut the option only showcased button 1 for assignment . what to do if I want to assign another button.@Jetson-Nano You set that parameter to match the button you want to use.
-
@Jetson-Nano You set that parameter to match the button you want to use.
@Eric-Katzfey Thank you for reverting back, The options only show one option button 1. I tested with button one but the drone was not taking in the command for enabling the turtle mode.
I want to know whether the code was tested out, so that I can be sure about not missing out on any parameter or setup -
@Eric-Katzfey Thank you for reverting back, The options only show one option button 1. I tested with button one but the drone was not taking in the command for enabling the turtle mode.
I want to know whether the code was tested out, so that I can be sure about not missing out on any parameter or setup@Jetson-Nano It's a parameter that you can set to any number you want. In QGC you can look at the joysticks tab and see as you press each button which number it is. Then set the parameter to that number.
-
@Jetson-Nano It's a parameter that you can set to any number you want. In QGC you can look at the joysticks tab and see as you press each button which number it is. Then set the parameter to that number.
@Eric-Katzfey I am not able to setup multiple buttons, it is only showing one option of
button 1.
Also after assigning the button one and trying to enable and use turtle mode, it is not working.
Is there any particular version of px4 that this works with.
My setup is VOXL 2 ---> TELEM 1 --> Flight core v2 --> TELEM 2 --> FPV ESC
In normal setup the motors are working and rotating, but when I try to keep the drone upside down and enable the turtle mode , the QGC is still showingnot readymessage. Also I am not able to ARM because of this.
Is there anything I am missing out? -
@Eric-Katzfey I am not able to setup multiple buttons, it is only showing one option of
button 1.
Also after assigning the button one and trying to enable and use turtle mode, it is not working.
Is there any particular version of px4 that this works with.
My setup is VOXL 2 ---> TELEM 1 --> Flight core v2 --> TELEM 2 --> FPV ESC
In normal setup the motors are working and rotating, but when I try to keep the drone upside down and enable the turtle mode , the QGC is still showingnot readymessage. Also I am not able to ARM because of this.
Is there anything I am missing out?@Eric-Katzfey could you please help me out here
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login