Cannot communicate over adb/fastboot after flashing image

Alex Kushleyev

@Kashish-Garg-0 , thanks for clarifying. Was this board working originally and then something happened or was it "dead" when you received it?

Kashish Garg 0

@Alex-Kushleyev it was working and we accidentally removed glibc in an attempt to upgrade it. Meaning we couldn't access the shell anymore.

Alex Kushleyev

@Kashish-Garg-0 , I understand.

Can you try this procedure to force into fastboot and then perform SDK install?

https://docs.modalai.com/voxl2-voxl2-mini-system-image/#force-voxl-2-into-fastboot

Kashish Garg 0

@Alex-Kushleyev Hey Alex, we have gone through this procedure a few times, even had a partner to make sure the button was being pressed appropriately. When running fastboot devices, no device gets identified.

Alex Kushleyev

@Kashish-Garg-0 , I understand, thanks for clarifying.

My colleague, who has more experience with this, was out of office last week, coming back tomorrow. I will make sure he takes a look at your post, he may have some suggestions. @tom

Alex

tom

@Kashish-Garg-0 With your device plugged in to your host pc via usb, what do you see with lsusb on your host PC?

Kashish Garg 0

@tom

Bus 005 Device 008: ID 05c6:900e Qualcomm, Inc.

Thanks for your help!

tom

@Kashish-Garg-0 Okay so the device is booting into EDL mode, which is what is used for QDL flashing. Can you confirm that the EDL switch is turned off?

Kashish Garg 0

@tom Yes the EDL Switch is turned OFF, pointing away from the Processor

tom

@Kashish-Garg-0 And when you went through the QDL process did the QDL flashing complete as expected? Should take around 10 minutes to complete

Kashish Garg 0

@tom I just re ran it and it took around 7 minutes or so and gave the appropriate output:

FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<log value="INFO: Calling handler for setbootablestoragedrive" /></data>
FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<log value="INFO: Using scheme of value= 1" /></data>
FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<response value="ACK" rawmode="false" /></data>
FIREHOSE WRITE: <?xml version="1.0"?>
<data><power value="reset"/></data>

FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<log value="INFO: Calling handler for power" /></data>
FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<response value="ACK" rawmode="false" /></data>

tom

@Kashish-Garg-0 And then if you remove and replace both power and usb is it still booting to that same mode?

Kashish Garg 0

@tom You mean is it going to EDL mode after replacing power/usb and moving the EDL Switch to off?

Bus 005 Device 011: ID 05c6:900e Qualcomm, Inc. USB2.0 Hub

Is what is being printed with lsusb now

tom

@Kashish-Garg-0 Sounds like we'll have get an RMA going for this one: https://www.modalai.com/pages/rma

tom

@Kashish-Garg-0 It's possible your board has a QSM8250 (M0054-2) instead of a QRB5165 (M0054-1), see here for the diffs: https://docs.modalai.com/m0054-versions/#m0054-1-and-m0054-2

If that is the case then you will have to QDL using a different build, which you can download from downloads.modalai.com, look for M0054-2 Starling QDL Image 1.7.4 2024-02-09-1.7.4-M0054-2.zip under the "All" category