Skip to content
  • Categories
  • Recent
  • Tags
  • Popular
  • Users
  • Groups
Collapse
Brand Logo

ModalAI Forum

  1. ModalAI Support Forum
  2. Development Drones
  3. Starling 2 Max – Using the AWUS036EACS in Japan (2.4 GHz only)

Starling 2 Max – Using the AWUS036EACS in Japan (2.4 GHz only)

Scheduled Pinned Locked Moved Unsolved Development Drones
4 Posts 2 Posters 54 Views 1 Watching
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Y Offline
    Y Offline
    yuta.ohtani
    wrote last edited by
    #1

    Hardware: Starling 2 Max, -M36 (Wi-Fi: Alfa AWUS036EACS)

    What I am trying to do:
    We are planning an outdoor field demonstration of the Starling 2 Max in Japan. To use the included Wi-Fi adapter under Japan's 180-day exemption for radio equipment without Japanese certification, we need to operate it only in the 2.4 GHz band at 200 mW or less. (We have read the answers in https://forum.modalai.com/topic/5530.)

    Could you help us with the following?

    1. 2.4 GHz-only operation: Can the adapter be set to use only 2.4 GHz and never transmit on 5 GHz, including at boot and after a reboot? If so, what settings should we use in SoftAP mode (hostapd.conf) and Station mode, and do they persist across reboots?

    2. Maximum transmit power: What is the maximum transmit power of the AWUS036EACS in the 2.4 GHz band? Can it be limited by software?

    3. Correct FCC ID: Could you tell us the correct FCC ID of the AWUS036EACS? The datasheet lists 2AB878811, but this ID appears to belong to the AWUS036ACS (RTL8811AU, no Bluetooth), and its frequency ranges match the AWUS036ACS entry on the VOXL 2 WiFi Setup page. Is the "Radio & FCC Report" linked in the AWUS036EACS row of that page the correct document?

    4. Bluetooth: Is the adapter's Bluetooth function enabled on the Starling 2 Max? If not, can we confirm that it does not transmit?

    Thank you for your help.

    Yuta Ohtani
    JDSC Inc.

    1 Reply Last reply
    0
    • tomT Online
      tomT Online
      tom
      admin
      wrote last edited by
      #2

      Hi Yuta,

      1. 2.4 GHz-only operation: Yes. Note that units ship configured as a 5 GHz SoftAP on channel 149, so configure the unit before the adapter is ever powered in Japan: unplug the WiFi adapter, connect over adb, set up 2.4 GHz mode, then plug the adapter back in. In SoftAP mode, "voxl-wifi softap <ssid> <password>" writes hw_mode=g and channel=6 to /data/misc/wifi/hostapd.conf, and the voxl-softap service starts hostapd from that file at every boot. Also set country_code=JP in that file. In Station mode, add "country=JP" and a 2.4 GHz "freq_list" to /etc/wpa_supplicant/wpa_supplicant-wlan0.conf so wpa_supplicant does not scan or associate on 5 GHz. Both files persist across reboots, but running voxl-wifi again regenerates them, so re-apply the edits after any voxl-wifi command. The exact steps are here: https://docs.modalai.com/voxl-2-wifi-setup/#regional-settings-and-24-ghz-only-operation

      2. Maximum transmit power: Alfa specifies 17 dBm (about 50 mW) typical output power with a 2 dBi antenna, which is below 200 mW without any software limit.

      3. FCC ID: You are correct, 2AB878811 is the AWUS036ACS grant, and that row on our WiFi Setup page was wrong (it also listed the wrong chipset). The AWUS036EACS uses the Realtek RTL8821CU. We have corrected the WiFi Setup page and the Starling 2 Max datasheet. For the AWUS036EACS grant itself, please confirm the FCC ID with Alfa Network directly, since they hold the certification.

      4. Bluetooth: The adapter is a WiFi and Bluetooth combo, but the VOXL 2 kernel does not include the btusb driver or the Realtek Bluetooth firmware. The Bluetooth radio is never initialized and no Bluetooth interface exists on the Starling 2 Max.

      1 Reply Last reply
      0
      • Y Offline
        Y Offline
        yuta.ohtani
        wrote last edited by
        #3

        Hi,

        Thank you very much for your thorough and helpful reply. The step-by-step instructions for 2.4 GHz-only operation, the clarification on Bluetooth, and especially your quick correction of the FCC ID on the WiFi Setup page and the Starling 2 Max datasheet are all greatly appreciated.

        First, I would like to explain some background, and I apologize for any confusion my earlier questions may have caused. My colleague, Hiroyuki Taguchi, placed the order and shared the Starling 2 Max product page with me. Since the page lists the Alfa AWUS036EACS as the Wi-Fi datalink, I based my questions on that adapter. However, when I inspected the actual unit, I found that its configuration was quite different from what the product page describes.

        The order details are as follows:

        • Confirmation: #UXDFP5VXH
        • Configuration: with Battery Pack and Controller / Dual 4k & Dual Tracking & ToF (C29) / WiFi and Ghost Atto 2.4GHz

        The unit we received came with the M0213 Wi-Fi board, which carries the Bots Unlimited Sparrow SP-01-100 module (FCC ID: 2BPPF-SP01, IC: 34356-SP01, HW REV 1.1) mounted directly on the VOXL 2. There is no Alfa adapter on the unit. A photo of the board is attached.

        Since your answers are based on the AWUS036EACS, I would be grateful if you could answer the same points for the M0213 / Sparrow:

        1. 2.4 GHz-only operation: Does the same procedure (country_code=JP in hostapd.conf, and country=JP with a 2.4 GHz freq_list in wpa_supplicant) apply to the M0213? Your instructions say to unplug the Wi-Fi adapter before the first power-up in Japan. Can the M0213 be safely removed from the VOXL 2 for the initial configuration, or can we use the Sparrow's hardware RF kill to keep the radio off until 2.4 GHz mode is set?

        2. Maximum transmit power: The M0213 documentation lists up to 30 dBm at 2.4 GHz, which exceeds 200 mW. What is the default transmit power on the Starling 2 Max, and how can we limit it to 23 dBm (200 mW) or less in a way that persists across reboots?

        3. FCC certification: Has the FCC grant for 2BPPF-SP01 been issued? The M0213 documentation page and the Bots Unlimited product page both list it as "pending." If it has not been issued, would it be possible to exchange the M0213 for a configuration with a confirmed FCC grant, such as the M0141 with the AWUS036ACS (FCC ID: 2AB878811)?

        4. Bluetooth: The Sparrow module also includes Bluetooth. Can you confirm that the Bluetooth radio is never initialized on the M0213, as with the Alfa adapter?

        In addition, could you provide official documentation showing the hardware configuration of the unit shipped for this order, including the Wi-Fi board and the R/C receiver? The product page and datasheet still list the AWUS036EACS.

        I understand this adds to your workload, and I truly appreciate your time and continued support. Your help is essential for us to operate the Starling 2 Max in compliance with Japanese radio regulations.

        Best regards,
        Yuta

        1 Reply Last reply
        0
        • tomT Online
          tomT Online
          tom
          admin
          wrote last edited by
          #4

          Hi Yuta,

          Thanks for checking the unit, and sorry for the confusion. Your unit's -M36 option is the M0213 VOXL 2 Wifi Addon (Bots Unlimited SP-01-100 "Sparrow"), not the Alfa adapter.

          2.4 GHz-only operation: Yes, the same procedure applies, with different interface names. The M0213 creates uap0 for SoftAP and mlan0 for Station, and can run both at once. In SoftAP mode, "voxl-wifi softap <ssid> <password>" writes hw_mode=g and channel=6 to /data/misc/wifi/hostapd.conf with interface=uap0; add country_code=JP to that file. For Station mode the file is /etc/wpa_supplicant/wpa_supplicant-mlan0.conf; add country=JP and the 2.4 GHz freq_list there, then restart wpa_supplicant@mlan0. If you do not need Station mode, leave it disabled. We added the M0213 interface names to the setup steps: https://docs.modalai.com/voxl-2-wifi-setup/#regional-settings-and-24-ghz-only-operation

          FCC certification: The FCC grant for FCC ID 2BPPF-SP01 was issued on September 24, 2025. Our M0213 page still said "pending"; it is now corrected: https://docs.modalai.com/m0213/

          Transmit power, Bluetooth, and RF kill: These depend on the Sparrow module's driver and firmware, so Bots Unlimited is the best source for the default transmit power, how to cap it at 23 dBm or less persistently, whether the Bluetooth radio can transmit, and how to use the hardware RF kill. You can reach them here: https://botsunlimited.com/contact/

          Hardware configuration: For official documentation of the configuration shipped on your order, please email contact@modalai.com with your order number.

          1 Reply Last reply
          0

          Reading along? Create a free ModalAI Forum account to join in.

          With an account you can reply, ask your own question, get an email when a ModalAI engineer answers, and mark the reply that solved it. Your place in each thread is saved between visits.

          Questions about VOXL, Flight Core, ESCs and ModalAI drones are answered here by the engineers who build them.

          Register Login
          Reply
          • Reply as topic
          Log in to reply
          • Oldest to Newest
          • Newest to Oldest
          • Most Votes


          ModalAI
          Categories Recent Tags ModalAI.com Docs
          © 2026 ModalAI® · Accelerating autonomy for smaller, smarter, safer drones · Powered by NodeBB
          • Login

          • Don't have an account? Register

          • Login or register to search.
          • First post
            Last post
          0
          • Categories
          • Recent
          • Tags
          • Popular
          • Users
          • Groups