Unable to configure LTE modem

h3robotics

@Alex-Kushleyev I agree. When I put in the USB3/UART Add on board, I see that there is some clearance b/w the JST connector and the LTE board.
So it looks like the LTE modem is seated in properly. Looking forward to a solution to my problem of LTE setup

tom

@h3robotics If the hardware is all good you should see the Sierra wireless device enumerate with lsusb and well as the network interface, wwan0 enumerate when you check ifconfig

h3robotics

@tom can you look at this topic I just created. It turns out I was wiring the 4-in-1 ESC wrong as per a wiring diagram in the documentation.

https://forum.modalai.com/topic/4366/error-in-voxl-mini-4-in-1-esc-diagram

Alex Kushleyev

@h3robotics , I believe you are correct that there is an error in the diagram. We will fix the diagram asap and work with you to make things right. Please give us a chance to evaluate what actually happens if the boards are connected in the way our diagram shows. Basically, it seems like the 3.3V from VOXL2 would be shorted to the GND on the ESC, but it needs further analysis.

Alex Kushleyev

@h3robotics , are you able to confirm ESC functionality without VOXL2 by connecting it to a power supply and usb-to-serial adapter (GND, RX, TX) to a Linux workstation? You can use voxl-esc tools to scan and test spin the ESC: https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/tree/master/voxl-esc-tools?ref_type=heads#scanning-for-escs

Also, as you connect the ESC to a power supply (lets say 12V), please note the current draw, which should be around 20-30mA for an idling ESC (motors not spinning) without any load connected to its power regulator outputs. Also, you can verify the blue LED behavior as described here:

https://docs.modalai.com/voxl-escs/faq/#q-what-is-the-behavior-of-the-four-blue-on-board-leds

Furthermore, please use a volt meter to confirm that the voxl power output from the ESC is at 5.0V. This regulator feeds VOXL2 but is also used for the ESC itself (as the first stage of power regulation).

Alex

h3robotics

@Alex-Kushleyev just to confirm that I need to use a USB-to-UART (TTLv3.3) cable and connect it to the UART port J1 of the ESC?
Thank you for working through this with me. Really appreciate the support!

h3robotics

@Alex-Kushleyev here are the results:

I connected the ESC to a power supply (12V) and USB-UART(3.3v) cable. I was able to successfully scan and spin the ESC. See screenshots below:

I did not have any motors connected to the ESC but I did the spin test. I did see the current on my power supply jump from 38mA to ~55mA and all four LEDs were blinking blue.

When idle (ESC not spinning), the power supply was showing a current between 36mA - 38mA.
On bootup, the ESC blue LEDs rapidly flash for 1 s and then 2-3 blue blinks and then no blinking. When I spin the ESCs, the blue LEDs start blinking maybe once every second.
Using a voltmeter, I can see 5V on the power output.

Let me know the next steps

Alex Kushleyev

@h3robotics , Thanks for running the test. Yes, 3.3V TTL signal is correct, since ESC uses 3.3V signal levels.

It looks like the ESC test is good so far (as much as we can see without spinning)

Next I would suggest the following:

unplug the LTE add-on board from VOXL2
plug in power from the mini ESC into VOXL2
plug in correct UART cable between VOXL2 and mini ESC
test the ESC from VOXL2:

adb shell
systemctl stop voxl-px4
cd /usr/share/modalai/voxl-esc-tools
./voxl-esc-scan.py
./voxl-esc-spin.py --id 255 --power 0

(the last command will not spin the motors but will print out the voltage and current).

Also while VOXL2 is running, please double check the 5V (going to VOXL2) is still 5V.

Alex

h3robotics

@Alex-Kushleyev I followed the steps. The ESC was detected in the scan:

Screenshot from 2025-04-23 21-58-21.png

and the run command executed as:

Screenshot from 2025-04-23 21-59-41.png

My power supply is at 7.4V since I intend to power the drone with 2S pack. In idle, the power supply shows ~132mA and during the spin test the power supply showed 135mA - 148mA.

Also the power output is 5V at the ESC when VOXL2 is connected.

Alex Kushleyev

@h3robotics , OK great, so far it seems like everything is working properly. The M0129 current sensing is accurate to within few hundred mA (because the range is very large, up to 100A+), so it is OK that it is not quite matching up with the 135mA actual current draw.

Is there any indication that VOXL2 is not working properly so far?

One more thing to check.. since there was a possibility of a short of 3.3V coming from VOXL2 to GND, let's check that. You can test it at VOXL2 pin 1 on J18 or also pin1 on J10 (https://docs.modalai.com/voxl2-connectors/#j18-uart-esc). You could plug in a JST GH connector into either port (maybe J10 is easier, since J18 is populated by the ESC connection) and carefully check voltage present between pin1 and GND.

I can see that 3.3V is fed into the LTE Modem board, so if 3.3V is not present, this would be an issue.

Alex