FLIR Lepton on Starling 2 Max
-
Is it possible to procure and plug in a FLIR Lepton 3.5 sensor into the Starling 2 Max as sold? I was told that there were potential SW issues, but it should work. One of the pictures on the Starling 2 Max product page suggests that this would only be supported on the C29 SKU/config; however, I only have C28 configs. Can you confirm that this will or will not work on the Starling 2 Max C28 config? Also, is this the correct sensor model: https://www.digikey.com/en/products/detail/flir-lepton/500-0771-01/7606616?s=N4IgTCBcDaIKwAYEFoEHY0EZWZAXQF8g
Thanks!
-
Is it possible to procure and plug in a FLIR Lepton 3.5 sensor into the Starling 2 Max as sold? I was told that there were potential SW issues, but it should work. One of the pictures on the Starling 2 Max product page suggests that this would only be supported on the C29 SKU/config; however, I only have C28 configs. Can you confirm that this will or will not work on the Starling 2 Max C28 config? Also, is this the correct sensor model: https://www.digikey.com/en/products/detail/flir-lepton/500-0771-01/7606616?s=N4IgTCBcDaIKwAYEFoEHY0EZWZAXQF8g
Thanks!
@RyanH , The FLIR Lepton socket should be included with your Starling 2 Max, you should be able to see it at the bottom. Assuming the socket is there, you just need to plug in Flir Lepton 3.5 and enable the
voxl-lepton-server.After installing
voxl-lepton-server, you will need to configure the correct i2c and spi port, as described here : https://docs.modalai.com/M0173/#downward-range-finder-and-flir-leptonThe link you provided seems to be a standard Flir Lepton 3.5, so it should work (160x120 resolution)

-
@RyanH , The FLIR Lepton socket should be included with your Starling 2 Max, you should be able to see it at the bottom. Assuming the socket is there, you just need to plug in Flir Lepton 3.5 and enable the
voxl-lepton-server.After installing
voxl-lepton-server, you will need to configure the correct i2c and spi port, as described here : https://docs.modalai.com/M0173/#downward-range-finder-and-flir-leptonThe link you provided seems to be a standard Flir Lepton 3.5, so it should work (160x120 resolution)

@Alex-Kushleyev , thanks! We'll give it a try and let you know how it goes.
-
Hi, I have a C29 config Starling 2 Max. Ryan, did you ever integrate the sensor?
I saw on this other post: https://forum.modalai.com/topic/4489/teledyne-flir-lepton-3-5-integration/2 @alex-kushleyev, you wrote that the "FLIR Lepton 3.5 just inserts into M0157 board which has the socket for the bare Lepton sensor." Sorry if this is too basic of a question, but am I to understand that if I purchase the FLIR Lepton 3.5 from the link above, that the integration is done by sliding the chip into the carrier/adapter(?) board through the opening? And it will be affixed by clicking into place? What orientation does the sensor go in?
-
yes, you can purchase the FLIR Lepton 3.5 and insert directly into the available socket. You will need to remove the plastic cover, which is shown in the image above, unfortunately the screw for that is on the other side of the frame, so you will need to take off VOXL2 in order to access the screws for the lepton cover. The Lepton sensor has a keyed socket, so it will only go in one way and will snap in place. The plastic cover is designed to prevent the sensor from falling out of the socket, since it's mounted facing down.
Reading along? Create a free ModalAI Forum account to join in.
With an account you can reply, ask your own question, get an email when a ModalAI engineer answers, and mark the reply that solved it. Your place in each thread is saved between visits.
Questions about VOXL, Flight Core, ESCs and ModalAI drones are answered here by the engineers who build them.
Register Login