Motor issues when running ESC calibration
-
@Alexander-Saunders, my bad too many zeros. 2,000,000 (2Mbit)
The screen shot in earlier post today shows running “voxl-esc” which is a wrapper for the python tools, sometimes it is easier just to use python tools directly, but make sure they are latest version. the version in /usr/share/modalai is probably not latest. Normally you dont need to update the tools but if something is not working as expected, it is good to try the latest.
-
The screen shot in earlier post today shows running “voxl-esc” which is a wrapper for the python tools, sometimes it is easier just to use python tools directly, but make sure they are latest version. the version in /usr/share/modalai is probably not latest. Normally you dont need to update the tools but if something is not working as expected, it is good to try the latest.
-
@Alexander-Saunders, my bad too many zeros. 2,000,000 (2Mbit)
No worries. We also verified if the issue was with the particular param file and ran the command to upload a different one. No luck with that and we still receive the same error (Bus 12, ESC not detected, etc)
-
No worries. We also verified if the issue was with the particular param file and ran the command to upload a different one. No luck with that and we still receive the same error (Bus 12, ESC not detected, etc)
Can you please try voxl-esc tools from dev branch on github? Instead of /usr/share/modalai/voxl-esc-tools
-
Can you please try voxl-esc tools from dev branch on github? Instead of /usr/share/modalai/voxl-esc-tools
Also, which SDK are you using? i am surprised to see this issue.
Also, can you please double check the ESC bootup sequence:
- apply power
- 4 blue leds flash quickly for 1 second, then turn off
- 4 blue leds blink twice
- motor makes a quick chirp (three tones based on the latest params that provided)
-
Also, which SDK are you using? i am surprised to see this issue.
Also, can you please double check the ESC bootup sequence:
- apply power
- 4 blue leds flash quickly for 1 second, then turn off
- 4 blue leds blink twice
- motor makes a quick chirp (three tones based on the latest params that provided)
@Alex-Kushleyev ESC gave
4 LEDs quickly flashing
4 LEDs flash 3 times
Motor chirps -
@Alex-Kushleyev ESC gave
4 LEDs quickly flashing
4 LEDs flash 3 times
Motor chirps -
Also, which SDK are you using? i am surprised to see this issue.
Also, can you please double check the ESC bootup sequence:
- apply power
- 4 blue leds flash quickly for 1 second, then turn off
- 4 blue leds blink twice
- motor makes a quick chirp (three tones based on the latest params that provided)
One more suggestion, it often helps to use a direct connection between the ESC and your linux PC and run the voxl-esc tools there. This way you can see the plots instantly during testing and also if there are some issues with communication to the ESC, you can always connect it to the PC and check the ESC that way.
Do you have a USB to serial adapter cable that plugs into the ESC <-> PC ?
-
@Alex-Kushleyev ESC gave
4 LEDs quickly flashing
4 LEDs flash 3 times
Motor chirps@rdjarvis said in Motor issues when running ESC calibration:
@Alex-Kushleyev ESC gave
4 LEDs quickly flashing
4 LEDs flash 3 times
Motor chirpsOK that is good!
-
One more suggestion, it often helps to use a direct connection between the ESC and your linux PC and run the voxl-esc tools there. This way you can see the plots instantly during testing and also if there are some issues with communication to the ESC, you can always connect it to the PC and check the ESC that way.
Do you have a USB to serial adapter cable that plugs into the ESC <-> PC ?
-
@Alex-Kushleyev, yes we have the USB/Serial connector.
@rdjarvis , ok great. Lets take a step back and just make sure you can talk to the ESC from the PC.
I will test SDK 1.2.0 to make sure it works fine with voxl-esc tools with my esc.
-
@rdjarvis , ok great. Lets take a step back and just make sure you can talk to the ESC from the PC.
I will test SDK 1.2.0 to make sure it works fine with voxl-esc tools with my esc.
-
@rdjarvis , ok great. Lets take a step back and just make sure you can talk to the ESC from the PC.
I will test SDK 1.2.0 to make sure it works fine with voxl-esc tools with my esc.
Also to confirm, I followed the README from dev branch to update.
-
Also to confirm, I followed the README from dev branch to update.
@Alexander-Saunders , thank you for confirming. I see that you are using SDK 1.2.0, which is very recent, so it already has (almost) the latest voxl-esc tools.
I am in the process of testing the tools on voxl2 using SDK 1.2.0, please try to connect to your PC directly and this should properly detect your ESC.
-
@Alexander-Saunders , thank you for confirming. I see that you are using SDK 1.2.0, which is very recent, so it already has (almost) the latest voxl-esc tools.
I am in the process of testing the tools on voxl2 using SDK 1.2.0, please try to connect to your PC directly and this should properly detect your ESC.
-
@Alex-Kushleyev
ssh'd into Linux PC.
Connected to ESC with USB to SERIAL
voxl2:/usr/share/modalai/voxl-esc-tools/voxl-esc-scan.pyreceived same error as Windows PC.
No ESCs detected
What do you mean "ssh'd into Linux PC" ?
I am suggesting to connect the ESC to a standalone Linux PC and run the
voxl-esc-scan.pyon the linux PC (not on VOXL2).Just wanted to clarify..
I tested the SDK 1.2.0 and the tools are working fine, it seems.
-
What do you mean "ssh'd into Linux PC" ?
I am suggesting to connect the ESC to a standalone Linux PC and run the
voxl-esc-scan.pyon the linux PC (not on VOXL2).Just wanted to clarify..
I tested the SDK 1.2.0 and the tools are working fine, it seems.
On the Linux PC we are directly connected to 4 pin JST on ESC to USB.
I ssh'd into VOXL2 from the Linux PC terminal.
I ran voxl-esc-scan.py in VOXL2 (same results) No ESCs detected.
I ran same command in Linux terminal (not ssh'd into VOXL2) same results. No ESCs detected.
This is including running same command in /usr/share/modalai/voxl-esc-tools/.voxl-esc-scan.py
RDJ
-
What do you mean "ssh'd into Linux PC" ?
I am suggesting to connect the ESC to a standalone Linux PC and run the
voxl-esc-scan.pyon the linux PC (not on VOXL2).Just wanted to clarify..
I tested the SDK 1.2.0 and the tools are working fine, it seems.
-
@Alex-Kushleyev power is on the UAV and ESC gave proper Flashes/Tones.
@rdjarvis , which serial to usb cable are you using? have you tested it with an ESC before? I am wondering if the RX/TX connections are correct and not swapped.
Also, do you have any other Modalai ESC you can test just to make sure the cables are working?
-
@rdjarvis , which serial to usb cable are you using? have you tested it with an ESC before? I am wondering if the RX/TX connections are correct and not swapped.
Also, do you have any other Modalai ESC you can test just to make sure the cables are working?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login