KDE 4012XF motors with 16 in props

Chase Riley

@Alex-Kushleyev Were you able to post the instructions you were talking about? I am waiting on them to run through before I can get out and flight test again.

Alex Kushleyev

@Chase-Riley , I am working on finalizing this.. should be done today within a few hours. I just wanted to double check - are you able to share which motors / props you are using? I just want to make sure the M0134-6 is powerful enough to support them. Also what battery voltage? 4S or 6S?

Chase Riley

@Alex-Kushleyev Would rather not share on here. If current draw is your worry I am below a 20 amp peak for each motor so the current 6s ESC should handle them fine. I also have a fan inside the AV blowing directly over the ESC.

Alex Kushleyev

@Chase-Riley , absolutely no problem regarding sharing the motor / propeller specs.

Alright, i have just posted initial instructions for low-kv motor tuning here : https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/blob/dev/voxl-esc-tools/doc/low_kv_motor_tuning.md . There is also a firmware update version 39 RC11 that you will need to install (this is part of the tuning instructions).

Please go ahead and work through the procedure. It is quite detailed and goes beyond what is needed just for low-kv motors, but it represents pretty rigorous initial test that should be performed to ensure your motor will operate smoothly under various conditions.

The parameter file ../voxl-esc-params/low_kv/mn4006_m0134_6_low_kv.xml should be a good start for your application, but do follow the instructions to check / update the params as instructed.

Please let me know if you run into any issue or need clarification.

The main idea behind testing new motor/prop combination is to start with "easy" tests and gradually ramp up the scope of test as you look at the data and become confident that it is working well. I would definitely avoid doing things like plugging in a new motor and prop and just going to 100% power command without a ramp :).

I will be improving / updating the instructions in the coming days and will keep you posted about any major updates.

Alex Kushleyev

@Chase-Riley , i forgot to mention.. a small fan blowing air over the ESC may not result in much cooling. Airflow from propellers could provide a lot more cooling than a small fan. Please keep an eye on the temperatures of the ESC. After you perform the tuning and calibration, you can run all 4 motors (loaded with propellers) on the bench at hover rpm (rpm needed for your vehicle to hover) for several minutes and look at the ESC temp (it will be printed live in the terminal when you use voxl-esc-spin.py test script.

Ideally the ESC temperature should stay below 60-70 C
80C is acceptable
90C is worrisome
100C and above is critical

ESC should still operate above 125C. The temperature on M0134-6 is measured inside the MCU, so the Mosfets are likely to be even hotter. At that point you will probably run into thermal runaway (the hotter the ESC gets, the faster it will continue to heat up) and eventually mosfets and / or copper traces may burn up.

Chase Riley

@Alex-Kushleyev I was able to install the new firmware to the ESC, however when I am trying to upload the new params file ../voxl-esc-params/low_kv/mn4006_m0134_6_low_kv.xml I receive the following error.

[GCC 8.4.0]
Found voxl-esc tools bin version: 1.2

INFO: Params file name : /usr/share/modalai/voxl-esc-params/low_kv/mn4006_m0134_6_low_kv.xml 
INFO: Params file size : 8365 bytes


VOXL Platform: M0054
Detected VOXL2 M0054 or M0104!
Found previous connection information in .voxl_esc_cache ..
Prioritizing /dev/slpi-uart-2 @ 250000
INFO: Scanning for ESC firmware: /dev/slpi-uart-2, baud: 250000
Sending library name request: libslpi_uart_bridge_slpi.so
Received standard error event 2
Sending initialization request
INFO: ESC(s) detected on port: /dev/slpi-uart-2, baud rate: 250000
INFO: ESCs detected:
INFO: ---------------------
ID: 0, SW: 39, HW: 41: Unknown Board
ID: 1, SW: 39, HW: 41: Unknown Board
ID: 2, SW: 39, HW: 41: Unknown Board
ID: 3, SW: 39, HW: 41: Unknown Board
---------------------
ERROR: ESC firmware version 39 is incompatible with params supported by this utility
       Acceptable ESC firmware versions are:  [38]```

Alex Kushleyev

@Chase-Riley please use the latest voxl-esc tools from dev branch:

git clone https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc.git -b dev

you can clone that directly to voxl2 and just use the python scripts directly (instead of voxl-esc wrapper), since you working on a custom esc tuning.

Some helpful tips here too : https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/blob/dev/voxl-esc-tools/recovery.md

Chase Riley

@Alex-Kushleyev I made sure to have the latest version and know I can not detect the esc. See below.

Detected Python version : 3.6.9 (default, Mar 10 2023, 16:46:00) 
[GCC 8.4.0]
Found voxl-esc tools bin version: 1.5
VOXL Platform: M0054
Detected RB5 Flight, VOXL2 M0054 or M0104!
INFO: Scanning for ESC firmware: /dev/slpi-uart-2, baud: 2000000
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
INFO: Scanning for ESC bootloader: /dev/slpi-uart-2, baud: 230400
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
WARNING: No ESC(s) detected
VOXL Platform: M0054
Detected RB5 Flight, VOXL2 M0054 or M0104!
INFO: Scanning for ESC firmware: /dev/slpi-uart-2, baud: 250000
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
INFO: Scanning for ESC bootloader: /dev/slpi-uart-2, baud: 230400
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
WARNING: No ESC(s) detected
VOXL Platform: M0054
Detected RB5 Flight, VOXL2 M0054 or M0104!
INFO: Scanning for ESC firmware: /dev/slpi-uart-2, baud: 921600
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
INFO: Scanning for ESC bootloader: /dev/slpi-uart-2, baud: 230400
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
WARNING: No ESC(s) detected
VOXL Platform: M0054
Detected RB5 Flight, VOXL2 M0054 or M0104!
INFO: Scanning for ESC firmware: /dev/slpi-uart-2, baud: 230400
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
INFO: Scanning for ESC bootloader: /dev/slpi-uart-2, baud: 230400
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
WARNING: No ESC(s) detected
VOXL Platform: M0054
Detected RB5 Flight, VOXL2 M0054 or M0104!
INFO: Scanning for ESC firmware: /dev/slpi-uart-2, baud: 57600
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
INFO: Scanning for ESC bootloader: /dev/slpi-uart-2, baud: 230400
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
WARNING: No ESC(s) detected
VOXL Platform: M0054
Detected RB5 Flight, VOXL2 M0054 or M0104!
INFO: Scanning for ESC firmware: /dev/slpi-uart-2, baud: 115200
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
INFO: Scanning for ESC bootloader: /dev/slpi-uart-2, baud: 230400
/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi
WARNING: No ESC(s) detected

ERROR: not all ESCs found

Alex Kushleyev

@Chase-Riley said in KDE 4012XF motors with 16 in props:

/usr/lib/libvoxl_io.so: undefined symbol: voxl_uart_init_legacy_slpi

this error means that you are using relatively old VOXL2 SDK -- the interface for the UART bridge (which connects the DSP uart to CPU) has changed.

Are you able to updated the VOXL2 SDK to 1.1.2? and then repeat the procedure using dev branch of voxl-esc ?

Chase Riley

@Alex-Kushleyev Would rather not update if possible. I have spent months getting everything to work in 1.0. What would be affected if I did make the upgrade? Would I lose any config or param files?

Alex Kushleyev

@Chase-Riley OK

In this case, please try voxl-esc from this commit : https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/tree/066b6308611ac162342a716689d1b4ebe82b1a63

This is right before the DSP bridge interface changed and it should support firmware 39 in param update:
https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/blob/066b6308611ac162342a716689d1b4ebe82b1a63/voxl-esc-tools/voxl-esc-upload-params.py#L58

However, still use the firmware and params that i originally posted for the low kv motor tuning

Alex Kushleyev

also tag 1.3.2 should work https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/tags/v1.3.2

Chase Riley

@Alex-Kushleyev 1.3.2 seemed to have got the job done. I will let you know if I run in to anymore issues while tuning the esc.

Alex Kushleyev

@Chase-Riley , great!

Now, the tools in latest dev branch have some improvements including plotting. Can you please try one more thing:

use voxl-esc dev branch
replace the following file from v1.3.2, which will allow you to use the old uart bridge interface : https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/blob/master/voxl-esc-tools/voxl_serial.py replace with https://gitlab.com/voxl-public/voxl-sdk/utilities/voxl-esc/-/blob/v1.3.2/voxl-esc-tools/voxl_serial.py

this will be easier to support

Alex Kushleyev

@Matthew-Wellner FYI