ModalAI Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Register
    • Login

    Voxl2/Microhard/NV Trip 2

    VOXL 2
    6
    29
    1806
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • VinnyV
      Vinny ModalAI Team @McMason
      last edited by

      Hi @McMason
      Of course, we want you to be successful!!
      That 4G modem board works just like the Microhard boards we have... you have the same USB hub and the same VBUS capabilities, and you do not need to install a modem to get that functionality.
      Hope that helps!

      1 Reply Last reply Reply Quote 0
      • M
        McMason
        last edited by

        @Vinny , made the decision to just go with MH for better downrange reception.

        Is there a guide or anything you can point me too that would be a good start to set up a non MIPI camera? it will be connected via ETH from the trip2

        I would be ecstatic if it were as simple as voxl-configure-cameras lol.

        VinnyV 1 Reply Last reply Reply Quote 0
        • VinnyV
          Vinny ModalAI Team @McMason
          last edited by

          @McMason
          Sorry, I'll have to tag team this one off to @tom or someone else from software...
          Not sure how the USB based cameras show up different (if they do) from MIPI based cameras.

          Keep us posted!!

          1 Reply Last reply Reply Quote 0
          • M
            McMason
            last edited by

            Will do @Vinny thank you again

            1 Reply Last reply Reply Quote 0
            • tomT
              tom admin
              last edited by

              @McMason For normal USB cameras (UVC), we use voxl-uvc-server. However, we haven't tested an ethernet to USB camera so I'm not sure how much guidance we'll be able to provide there.

              1 Reply Last reply Reply Quote 0
              • M
                McMason
                last edited by McMason

                @vinny Is there any other VREG_S4A_1P8V test pads beside TP21 i can get power from on the bottom of the MH carrier? I put a meter to verify power and wasnt getting voltage out

                VinnyV 1 Reply Last reply Reply Quote 0
                • VinnyV
                  Vinny ModalAI Team @McMason
                  last edited by

                  @McMason
                  TP21 is it unfortunately.
                  All the rest are component pads which can easily break something. Right next to it is TP17 which is a GND.
                  This is only present on the "plug-in" version FYI (even if it's obvious, I need to say it) and it's not present on the dongle based versions (but in which case you can't have access to the UART either).
                  b04c0005-63c1-43a8-9f78-a928c97b8a2a-image.png

                  1 Reply Last reply Reply Quote 0
                  • M
                    McMason
                    last edited by

                    @Vinny Thank you. Looks like ill be getting something on order soon.

                    1 Reply Last reply Reply Quote 0
                    • R
                      rogerli
                      last edited by

                      Hello @McMason ,
                      Have you successfully connected VOXL2 and NV Trip2? Currently, I am using Ethernet and the Microhard Add-on board to connect VOXL2 and NV Trip2, and I can confirm successful connection using the ping command. However, I am unable to perform image transmission. Do you have any suggestions on how to resolve this issue?

                      Chase RileyC 1 Reply Last reply Reply Quote 0
                      • Chase RileyC
                        Chase Riley @rogerli
                        last edited by

                        @rogerli or @McMason Were either of you successful in getting the VOXL2 to connect to the NV Trip2? Working the same issue on my end.

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Powered by NodeBB | Contributors