VOXL 2 Camera Connected but Not Feed

[tom]

@Wesley-Gunawan Can you post the contents of /etc/modalai/voxl-camera-server.conf ?

[tom]

@tom As well as the output of voxl-inspect-sku

[Wesley Gunawan]

Hi Tom, I only have the access to the device several days a week, please let me know the complete information you need if further information is needed. Here is the outputs requested:

voxl2:~$ cat /etc/modalai/voxl-camera-server.conf
/**

• voxl-camera-server Configuration File
• Each camera has configurations for up to 4 HAL3 streams:
• • preview stream for raw unprocessed images from CV cameras
• • small_video 720p (ish) h264/h265 compressed for fpv video streaming
• • large_video 4k (ish) h264/h265 for onboard video recording to disk
• • snapshot ISP-processed JPG snapshots that get saved to disk
• on QRB5165 platforms (VOXL2 and VOXL2 mini) you can only have 3 of the 4 enabled
• This file is generated from default values by voxl-configure-cameras.
• Do not expect arbitrary resolutions to work, the ISP and video compression
• pipelines only support very specific resolutions.
• The default video compression mode is cqp or Constant Quantization Parameter

*/
{
"version": 0.1,
"fsync_en": false,
"fsync_gpio": 109,
"cameras": [{
"type": "imx412",
"name": "hires",
"enabled": true,
"camera_id": 0,
"fps": 30,
"en_preview": false,
"preview_width": 640,
"preview_height": 480,
"en_raw_preview": false,
"en_small_video": true,
"small_video_width": 1024,
"small_video_height": 768,
"small_venc_mode": "h265",
"small_venc_br_ctrl": "cqp",
"small_venc_Qfixed": 30,
"small_venc_Qmin": 15,
"small_venc_Qmax": 40,
"small_venc_nPframes": 9,
"small_venc_mbps": 2,
"en_large_video": true,
"large_video_width": 3840,
"large_video_height": 2160,
"large_venc_mode": "h265",
"large_venc_br_ctrl": "cqp",
"large_venc_Qfixed": 38,
"large_venc_Qmin": 15,
"large_venc_Qmax": 50,
"large_venc_nPframes": 29,
"large_venc_mbps": 30,
"en_snapshot": true,
"en_snapshot_width": 3840,
"en_snapshot_height": 2160,
"exif_focal_length": 0,
"exif_focal_length_in_35mm_format": 0,
"exif_fnumber": 0,
"ae_mode": "isp"
}]
}
voxl2:~$ voxl-inspect-sku

family code: TF-M0054 (voxl2-test-fixture)
compute board: 4 (voxl2)
hw version: 1
cam config: 11
modem config: 0 (none)
tx config: 0 (none)
extras config: 0 (none)
SKU: TF-M0054-4-V1-C11

[Wesley Gunawan]

@tom ^ (Reminder)

[itsnav]

@Wesley-Gunawan Hi Wesley, I faced a similar issue recently. I was using IMX678 Hires Camera in J7U. The camera was detected when I run voxl-camera-server -l, even the green led light on the sensor glows but I didn't get any data run I run voxl-inspect-cam -a. I had an alternate IMX678 camera and without changing any config, I replaced it and it worked. I don't know what is wrong with the first sensor. I should probably do RMA, but yeah, if you have another sensor, give it a try!

[Moderator]

@Wesley-Gunawan can you please share a picture of your setup? It needs to match a camera config found here: https://docs.modalai.com/voxl2-camera-configs/

Often when a camera can't be found:

1. it's installed backwards
2. the cable isn't fully connected or the connector is damaged
3. the wrong camera config has been configured during setup

[Wesley Gunawan]

@Moderator

Hi, the camera is connected correctly because when the configuration or installation setup isn't correct, voxl-camera-server wouldn't even detect the camera's connection, in this case it does, but no input from the camera has ever been acquired. Here is the image of the setup:

Is there any other information you need to help me debug this issue? It's been over a week and I need it working as soon as possible or else I have to return the whole kit. As for the camera defect possibility suggested by a user in this forum last week, I already tried swapping the camera and it still doesn't work.

[Moderator]

@Wesley-Gunawan It looks like you are using a C08 config. https://docs.modalai.com/voxl2-camera-configs/#c8---hires-only

Have you tried voxl-configure-cameras 8 ?

voxl-camera-server documentation for troubleshooting recommends running voxl-camera-server -d0. Can you try that and paste the output?

[Wesley Gunawan]

@Moderator It is camera configuration 8, the board wouldn't detect the camera otherwise (tried that before) so I'm assuming the camera configuration is correct.

voxl2:~$ voxl-camera-server -d0
existing instance of voxl-camera-server found, attempting to stop it
detected system image 1.7.8
using new imx412 defaults

configuration for 1 cameras:

cam #0
name: hires
sensor type: imx412
isEnabled: 1
camId: 0
camId2: -1
fps: 30
en_rotate: 0
en_rotate2: 0

en_preview:          0
pre_width:           640
pre_height:          480
en_raw_preview:      0

en_small_video:      1
small_video_width:   1024
small_video_height:  768

en_large_video:      1
large_video_width:   3840
large_video_height:  2160

en_snapshot:         1
snap_width:          3840
snap_height:         2160
exif_focal_length:   0.000000
exif_focal_len_35mm_format:0
exif_fnumber:        0.000000

ae_mode:             isp
msv_exposure_min_us: 20
msv_exposure_max_us: 33000
standby_enabled:     0
decimator:           1
independent_exposure:0

fsync_en: 0
fsync_gpio: 109

DEBUG: Attempting to open the hal module
DEBUG: SUCCESS: Camera module opened on attempt 0
DEBUG: ----------- Number of cameras: 1

VERBOSE: cci-direct: using voxl_platform_mod config 0 layout
DEBUG: Cam idx: 0, Cam slot: 2, Slave Address: 0x0034, Sensor Id: 0x0577
connected to mavlink pipe
DEBUG: ------ voxl-camera-server: Starting 1 cameras
Starting Camera: hires (id #0)
DEBUG: Checking Gain limits for Camera: hires
DEBUG: Using gain limits min: 100 max: 1600
DEBUG: cam ID 0 checking for fmt: 35 w: 1024 h: 768 o: 0
DEBUG: ==> option 0: format= 34 width=4056 height=3040 is_input=0
DEBUG: ==> option 4: format= 34 width=4056 height=3040 is_input=1
DEBUG: ==> option 8: format= 35 width=4056 height=3040 is_input=0
DEBUG: ==> option 12: format= 35 width=4056 height=3040 is_input=1
DEBUG: ==> option 16: format= 33 width=4056 height=3040 is_input=0
DEBUG: ==> option 20: format= 34 width=4000 height=3000 is_input=0
DEBUG: ==> option 24: format= 34 width=4000 height=3000 is_input=1
DEBUG: ==> option 28: format= 35 width=4000 height=3000 is_input=0
DEBUG: ==> option 32: format= 35 width=4000 height=3000 is_input=1
DEBUG: ==> option 36: format= 33 width=4000 height=3000 is_input=0
DEBUG: ==> option 40: format= 34 width=3840 height=2160 is_input=0
DEBUG: ==> option 44: format= 34 width=3840 height=2160 is_input=1
DEBUG: ==> option 48: format= 35 width=3840 height=2160 is_input=0
DEBUG: ==> option 52: format= 35 width=3840 height=2160 is_input=1
DEBUG: ==> option 56: format= 33 width=3840 height=2160 is_input=0
DEBUG: ==> option 60: format= 34 width=3264 height=2448 is_input=0
DEBUG: ==> option 64: format= 34 width=3264 height=2448 is_input=1
DEBUG: ==> option 68: format= 35 width=3264 height=2448 is_input=0
DEBUG: ==> option 72: format= 35 width=3264 height=2448 is_input=1
DEBUG: ==> option 76: format= 33 width=3264 height=2448 is_input=0
DEBUG: ==> option 80: format= 34 width=3200 height=2400 is_input=0
DEBUG: ==> option 84: format= 34 width=3200 height=2400 is_input=1
DEBUG: ==> option 88: format= 35 width=3200 height=2400 is_input=0
DEBUG: ==> option 92: format= 35 width=3200 height=2400 is_input=1
DEBUG: ==> option 96: format= 33 width=3200 height=2400 is_input=0
DEBUG: ==> option 100: format= 34 width=2976 height=2976 is_input=0
DEBUG: ==> option 104: format= 34 width=2976 height=2976 is_input=1
DEBUG: ==> option 108: format= 35 width=2976 height=2976 is_input=0

(Too much to show, at the end of the output):

VERBOSE: Dumping GBM flags
DEBUG: Found flag GBM_BO_USAGE_CPU_READ_QTI
DEBUG: Found flag GBM_BO_USAGE_CAMERA_WRITE_QTI
DEBUG: Allocated BO with width=25054814 height=1 stride=25054814 aligned_w=25054814 aligned_h=1 size=25054814 flags=0x20003 format=GBM_FORMAT_BLOB fd=226 vaddr=0x7fe8aaae70
DEBUG: Successfully set up pipeline for stream: SNAPSHOT
DEBUG: Started Camera: hires

------ voxl-camera-server: Started 1 of 1 cameras

------ voxl-camera-server: Camera server is now running
VERBOSE: Entered thread: cam0-result(tid: 2676)
VERBOSE: Entered thread: cam0-request(tid: 2675)
VERBOSE: added request for small video stream
VERBOSE: Sending request for frame 0 for camera hires for 1 streams
VERBOSE: Received result from HAl3 for frame number 0
VERBOSE: Received 0 buffers from camera hires, partial result:1
VERBOSE: finished sending request for frame 0 for camera hires
VERBOSE: returning from SendOneCaptureRequest for frame 1 for camera hires
VERBOSE: added request for small video stream
VERBOSE: Sending request for frame 1 for camera hires for 1 streams
VERBOSE: finished sending request for frame 1 for camera hires
VERBOSE: returning from SendOneCaptureRequest for frame 2 for camera hires
VERBOSE: added request for small video stream
VERBOSE: Sending request for frame 2 for camera hires for 1 streams
VERBOSE: finished sending request for frame 2 for camera hires
VERBOSE: returning from SendOneCaptureRequest for frame 3 for camera hires
VERBOSE: added request for small video stream
VERBOSE: Sending request for frame 3 for camera hires for 1 streams
VERBOSE: finished sending request for frame 3 for camera hires
VERBOSE: returning from SendOneCaptureRequest for frame 4 for camera hires
VERBOSE: added request for small video stream
VERBOSE: Sending request for frame 4 for camera hires for 1 streams
VERBOSE: finished sending request for frame 4 for camera hires
VERBOSE: returning from SendOneCaptureRequest for frame 5 for camera hires
VERBOSE: added request for small video stream
VERBOSE: Sending request for frame 5 for camera hires for 1 streams
VERBOSE: Received result from HAl3 for frame number 1
VERBOSE: Received 0 buffers from camera hires, partial result:1
VERBOSE: Received result from HAl3 for frame number 2
VERBOSE: Received 0 buffers from camera hires, partial result:1
DEBUG: Value of standby_active is: 0
DEBUG: Value of standby_active is: 0

received SIGINT Ctrl-C

------ voxl-camera-server: Camera server is now stopping
DEBUG: Stopping Camera: hires
Killed

[Moderator]

@Wesley-Gunawan that looks like it's running properly. Can you open another terminal and run voxl-inspect-cam -a ?

[Wesley Gunawan]

@Moderator I already tried that in the past, even before I consulted this forum, the output has always been like this

[Moderator]

@Wesley-Gunawan Can you please set and run inspect-cam again?

"en_preview": true,

"en_snapshot": false,

[Wesley Gunawan]

@Moderator voxl-camera-server -d0
existing instance of voxl-camera-server found, attempting to stop it
detected system image 1.7.8
using new imx412 defaults

configuration for 1 cameras:

cam #0
name: hires
sensor type: imx412
isEnabled: 1
camId: 0
camId2: -1
fps: 30
en_rotate: 0
en_rotate2: 0

en_preview:          1
pre_width:           640
pre_height:          480
en_raw_preview:      0

en_small_video:      1
small_video_width:   1024
small_video_height:  768

en_large_video:      1
large_video_width:   3840
large_video_height:  2160

en_snapshot:         0
snap_width:          3840
snap_height:         2160
exif_focal_length:   0.000000
exif_focal_len_35mm_format:0
exif_fnumber:        0.000000

ae_mode:             isp
msv_exposure_min_us: 20
msv_exposure_max_us: 33000
standby_enabled:     0
decimator:           1
independent_exposure:0

fsync_en: 0
fsync_gpio: 109

DEBUG: Attempting to open the hal module
DEBUG: SUCCESS: Camera module opened on attempt 0
DEBUG: ----------- Number of cameras: 1

(Too long, in the end):

------ voxl-camera-server: Camera server is now running
VERBOSE: Entered thread: cam0-request(tid: 2735)
DEBUG: Value of standby_active is: 0

received SIGINT Ctrl-C

------ voxl-camera-server: Camera server is now stopping
DEBUG: Stopping Camera: hires
DEBUG: ------ Last request frame for hires: 0
VERBOSE: Leaving hires request thread
DEBUG: ------ Last hires result frame: -1
VERBOSE: Leaving hires result thread
DEBUG: ------ Last frame encoded: -1
DEBUG: OMX_EventCmdComplete
DEBUG: OMX_EventCmdComplete
DEBUG: OMX_EventCmdComplete
DEBUG: ------ Last frame encoded: -1
DEBUG: OMX_EventCmdComplete
DEBUG: OMX_EventCmdComplete
DEBUG: Deleting buffers for hires preview stream
DEBUG: OMX_EventCmdComplete
DEBUG: Deleting buffers for hires small video stream
DEBUG: Deleting buffers for hires large video stream
DEBUG: Deleting buffers for hires snapshot stream
free(): invalid pointer
Aborted

voxl-inspect-cam -a output is the picture attached

[Moderator]

@Wesley-Gunawan did voxl-inspect-cam show anything while voxl-camera-server was running? it looks like you restarted voxl-camera-server while voxl-inspect-cam was running.

I think the proper steps are:

1. update config (done)
2. reboot VOXL 2
3. run voxl-inspect-cam -a

[Wesley Gunawan]

@Moderator

This is after power cycle (poweroff -f, power source off, turn on again)