ModalAI Forum

@modaltb I see.

Just one last thing, do you think a gimbal of ~900g would be ok to be attached to the Sentinel without any issues? As the quoted max. payload for the Sentinel is 1kg?

@modaltb I see. Thanks for the heads-up.

Any suggestions on how can I get an easy-to-use gimbal attachment to work with the Sentinel? The simplest for now, but I should be able to control it while getting the live stream.

@modaltb Which Gimbal(s) did you try from Gremsy? They are a bit expensive so I wanted to see if the ones you tried satisfy my requirements, I might as well get the same one.

@modaltb I see. In this case, what should be the work around if I really need to control the gimbal?

@admin Thank you for the response.

On the link you posted, it says

Interface
Communication Interface for Control Signal: USB(UVC) / CAN(DroneCAN)

Does this mean we can use either of them and we can still control the pan/tilt/zoom through UVC?

Hello,

I am planning to integrate the XACTIC CX-GB300 (Multispectral gimbal camera) with my Sentinel drone.

ドローンカメラ

ドローンカメラ製品ページ。独自のブレ補正機能 エクスタビライザ搭載で、ドローン飛行時の揺れを抑えた映像を撮影出来ます。

手振れ補正ウェアラブルカメラで遠隔支援｜株式会社ザクティ (xacti-co.com)

Following these instructions I am guessing I will have to buy an add-on board (Which I already have since I have the LTE 5G Modem), and the 4-pin JST to USB 2.0 Type A Female (MCBL-00009-1).

Now, can anyone guide me about the next steps required for the integration

@Alex-Kushleyev Ohh.

Yes please let me know how can I. I'm afraid I'll be needed spare parts for my research.

@Alex-Kushleyev I would prefer a carbon frame.

Is it a standard frame I can buy online? Like the S500 frame for the Sentinel?

Hello,

Where can I get a spare body for the Starling V2, in case I break this one?

Is there a 3D file I can use to print my own spare?

I've recently ordered the Starling drone and I am unsure about the R/C controller options of this drone.

The Starling webpage features an iFlight Commando 8 Radio Transmitter, but I wanted to confirm if I buy any other ELRS 915MHz Radio transmitter and it should work, right?

@SMRazaRizvi Issue resolved.
I connected one of the camera ports in a wrong orientation.

@SMRazaRizvi The Unbricking, however, was successfull. Below are the last few lines from the output, and at some point inside the output I said [PROGRAM] flashed "system" successfully

FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<log value="INFO: Calling handler for patch" /></data>
LOG: INFO: Calling handler for patch
FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<response value="ACK" rawmode="false" /></data>
FIREHOSE WRITE: <?xml version="1.0"?>
<data><setbootablestoragedrive value="1"/></data>

FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<log value="INFO: Calling handler for setbootablestoragedrive" /></data>
LOG: INFO: Calling handler for setbootablestoragedrive
FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<log value="INFO: Using scheme of value= 1" /></data>
LOG: INFO: Using scheme of value= 1
FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<response value="ACK" rawmode="false" /></data>
partition 1 is now bootable
FIREHOSE WRITE: <?xml version="1.0"?>
<data><power value="reset"/></data>

FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<log value="INFO: Calling handler for power" /></data>
LOG: INFO: Calling handler for power
FIREHOSE READ: <?xml version="1.0" encoding="UTF-8" ?>
<data>
<response value="ACK" rawmode="false" /></data>

@SMRazaRizvi I even performed the Unbricking steps as mentioned here but the issue persists.

@Alex-Kushleyev Alright, thanks.

Hello,

I am trying to connect to my Sentinel drone over the USB, but suddenly it doesn't connect using the adb shell.

My laptop can see the USB device when I do run lsusb

Bus 001 Device 016: ID 05c6:900e Qualcomm, Inc. QUSB_BULK_SN:EBC5FC33
but when I run adb shell it says

error: no devices/emulators found

Please help.

@Alex-Kushleyev Sure. its variant=45182917640496

@Alex-Kushleyev I haven't received my Starling yet. I'm trying to arrange the spare parts while I wait for the drone to be delivered.

The ones shown on the product page on the website were silver in color.

Anyways, the config for both silver and black is 1504, 3000kv, right?

@Alex-Kushleyev I have recently placed an order for it so haven't received them yet.

Should I expect them to be like this (black?)
If yes, can you please mention the configuration for these motors?

Hello,

I'm trying to find motor replacements for the Starling.

The Starling V2 Datasheet mentioned 1504 Motors, but do not mention the kV with it.

Can anyone please confirm the exact Specs. of the motors?

@Moderator Perfect. Thanks.