Hi,

In this video (https://www.youtube.com/watch?v=EhlXogRwWdQ) posted by ModalAI, you show the VIO capabilities in low light conditions. To replicate this, I am curious about the setup of the flashlight and the connection on the VOXL.
I need a flashlight that we can connect using USB or I2C on the VOXL/VOXL2. Do you have any product recommendations and/or ports we can use to connect the flashlight to on the VOXL/VOXL2?

Thanks,

Rohit

Thanks! I just had to manually focus it.

@Nishkala I used this link - https://docs.modalai.com/voxl2-system-image/#force-voxl-2-into-fastboot

You will need the latest platform release which can be found here - https://developer.modalai.com/asset/2

I re-flashed the drone with the new VOXL2 package and it seems to have fixed itself for the time being. I will post in this thread again if the issue springs back up.

Hi,

I am new to the Remote ID rule that the FAA put out a couple of months ago. I had a few questions about the voxl-remote-id service.

1. From the instructions, the voxl-remote-id service generates a remote ID for you. To register new drones now, you need to add either a standard Remote ID or a broadcast Remote ID. Is this a standard Remote ID or a broadcast one?
2. Does this remote ID change after a reboot? If so will we need to change our registration each time since the Remote ID is different with every bootup?
3. How do other parties see our broadcast information if not on softAP/Wifi? What if we were using our own radio network? For this case, is it better to buy our own out-of-the-box Remote ID broadcasting module?

Looking forward to hearing from you soon!

Thanks,

Rohit

Hi,

I am wondering how to change the default SSH password from oelinux123 to something else? If this is possible, how does one do this?

Thanks,

Rohit

Hi,

I am curious to know why there are 2x XT60 connectors on the Power module. Can either the Male or Female end of the connector be used to power the VOXL/VOXL2? Or should we only use the Male connector (the connector that connects to the wall power supply)?

Thanks!

Hi,

I am new to the Remote ID rule that the FAA put out a couple of months ago. I had a few questions about the voxl-remote-id service.

1. From the instructions, the voxl-remote-id service generates a remote ID for you. To register new drones now, you need to add either a standard Remote ID or a broadcast Remote ID. Is this a standard Remote ID or a broadcast one?
2. Does this remote ID change after a reboot? If so will we need to change our registration each time since the Remote ID is different with every bootup?
3. How do other parties see our broadcast information if not on softAP/Wifi? What if we were using our own radio network? For this case, is it better to buy our own out-of-the-box Remote ID broadcasting module?

Looking forward to hearing from you soon!

Thanks,

Rohit

I found out that the WiFi dongles were broken which is what was causing the issue

@Chad-Sweet I am also curious about the autotune feature and when it will be released. Any updates on this at this time?

Yep. It seems to be random. We tried different WiFi dongles and while it would fix the issue temporarily. It would cause issues a few days later.

Hi,

I am attempting to connect to the WiFi using the Microhard Add-on board and the ALFA wifi dongle connected to the board using the JST USBA adapter. However, when I do voxl-wifi station <SSID> <Password>. Nothing happens. No IP address is being seen under wlan0when I do ifconfig. I made sure the SSID and password are correct. Is this a known issue recently cause I don't remember having this much trouble before. This is a brand new VOXL2 board running 0.9.5.

Hi,

I noticed you guys released a new VOXL2 image over the past week and I had a question about it. Here - https://docs.modalai.com/voxl2-camera-configs/#platform-release-095 you mention that this image allows for more camera configs. But when I do voxl-configure-cameras I don't see these options that are shown in the link I provided. Could you guide me on how to get the new camera configs working?

Thanks!

Thanks for the info! Just to confirm, I am asking about this post ModalAI made on LinkedIn - https://www.linkedin.com/posts/modal-ai_voxl-tof-pmd-activity-7010997849232474112-VV6a?utm_source=share&utm_medium=member_desktop

This update is almost a year out?

Thanks.

Hi,

I am just wondering when the image will be released that supports 4 TOFs on the VOXL2. Or if it has, is there documentation on how to set this up?

Thanks!