ModalAI Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Register
    • Login

    GPS not working

    Sentinel
    7
    49
    4870
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • A
      Andre Moura @Eric Katzfey
      last edited by

      @Eric-Katzfey Unfortunately the GPS is not working as expected. Yesterday we were momentarily able to get between 9-12 satellites, which I think is a little low. With that number of satellites, we were not able to get GPS lock on the drone, QGC displayed an error related to GPS accuracy too low. Even after allowing to arm without GPS lock and flying at about 15 m, the number of satellites didn't change and we couldn't even put the drone in position mode, because of not being GPS locked.

      What we did to be able to even get those satellites was systemctl disable voxl-px4 , systemctl disable voxl-mavlink-server, rebooted the drone and, in two different ssh shells, ran both services manually.

      Today, using this approach, I'm not even able to get any satellites at all. All the following tests were done with the ekf2_outdoor_gps_mag.params configuration file from your Gitlab.

      The output from voxl-px4 was:

      voxl2:~$ voxl-px4
Found DSP signature file
INFO  [px4] mlockall() enabled. PX4's virtual address space is locked into RAM.
INFO  [px4] assuming working directory is rootfs, no symlinks needed.

______  __   __    ___ 
| ___ \ \ \ / /   /   |
| |_/ /  \ V /   / /| |
|  __/   /   \  / /_| |
| |     / /^\ \ \___  |
\_|     \/   \/     |_/

px4 starting.

INFO  [px4] Calling startup script: /bin/sh /etc/modalai/voxl-px4.config 0
Running on M0054
INFO  [muorb] SLPI: Creating qurt thread hpwork

INFO  [muorb] SLPI: Successfully created px4 task PX4_hpwork with tid 82
INFO  [muorb] SLPI: Creating qurt thread lpwork

INFO  [muorb] SLPI: Successfully created px4 task PX4_lpwork with tid 81
INFO  [muorb] SLPI: Creating qurt thread wkr_hrt

INFO  [muorb] SLPI: Successfully created px4 task PX4_wkr_hrt with tid 80
INFO  [muorb] SLPI: Creating qurt thread client_sync_thread

INFO  [muorb] SLPI: Successfully created px4 task PX4_client_sync_thread with tid 79
INFO  [muorb] SLPI: Creating qurt thread wq_manager

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_manager with tid 78
INFO  [muorb] SLPI: Creating qurt thread qshell

INFO  [muorb] SLPI: Successfully created px4 task PX4_qshell with tid 77
INFO  [qshell] Send cmd: 'icm42688p start -s'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: icm42688p start -s
INFO  [muorb] SLPI: Creating qurt thread wq_SPI1

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_SPI1 with tid 76
INFO  [muorb] SLPI: *** SPI Device ID 0x26000a 2490378
INFO  [uorb] Advertising remote topic sensor_accel
INFO  [uorb] Marking DeviceNode(parameter_server_set_used_request) as advertised in process_remote_topic
INFO  [muorb] SLPI: Marking DeviceNode(parameter_server_set_used_response) as advertised in process_remote_to
INFO  [uorb] Advertising remote topic sensor_gyro
INFO  [uorb] Advertising remote topic imu_server
INFO  [muorb] SLPI: on SPI bus 1
INFO  [muorb] SLPI: icm42688p #0 on SPI bus 1 (devid=0x0)
INFO  [muorb] SLPI: 

INFO  [muorb] SLPI: Ok executing command: icm42688p start -s
INFO  [muorb] SLPI: Sending qshell retval with timestamp 23323798, current timestamp 23323799
INFO  [uorb] Advertising remote topic qshell_retval
INFO  [qshell] qshell return value timestamp: 23323798, local time: 23327958
INFO  [muorb] SLPI: Marking DeviceNode(parameter_client_reset_request) as advertised in process_remote_topic
ERROR [muorb] SLPI: Cannot reset all parameters on client side
INFO  [uorb] Marking DeviceNode(parameter_client_reset_response) as advertised in process_remote_topic
INFO  [muorb] SLPI: Advertising remote topic parameter_update
INFO  [muorb] SLPI: Marking DeviceNode(parameter_client_set_value_request) as advertised in process_remote_to
INFO  [uorb] Marking DeviceNode(parameter_client_set_value_response) as advertised in process_remote_topic
INFO  [logger] logger started (mode=all)
Starting Holybro magnetometer
INFO  [qshell] Send cmd: 'ist8310 start -R 10 -X -b 1'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: ist8310 start -R 10 -X -b 1
INFO  [muorb] SLPI: Creating qurt thread wq_I2C1

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_I2C1 with tid 75
INFO  [muorb] SLPI: *** I2C Device ID 0x60e09 396809
INFO  [muorb] SLPI: ist8310 #0 on I2C bus 1 (external)

INFO  [muorb] SLPI: Ok executing command: ist8310 start -R 10 -X -b 1
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26405496, current timestamp 26405497
INFO  [qshell] qshell return value timestamp: 26405496, local time: 26406391
Starting Holybro LED driver
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: rgbled_ncp5623c start -X -b 1 -f 400 -a 56
INFO  [muorb] SLPI: *** I2C Device ID 0x7b3809 8075273
INFO  [qshell] Send cmd: 'rgbled_ncp5623c start -X -b 1 -f 400 -a 56'
INFO  [muorb] SLPI: rgbled_ncp5623c #0 on I2C bus 1 (external)

INFO  [muorb] SLPI: Ok executing command: rgbled_ncp5623c start -X -b 1 -f 400 -a 56
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26445017, current timestamp 26445018
INFO  [qshell] qshell return value timestamp: 26445017, local time: 26445673
INFO  [qshell] Send cmd: 'icp10100 start -I -b 5'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: icp10100 start -I -b 5
INFO  [muorb] SLPI: Creating qurt thread wq_I2C5

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_I2C5 with tid 74
INFO  [muorb] SLPI: *** I2C Device ID 0x9c6329 10249001
INFO  [muorb] SLPI: probe probe succeeded. data = 0x1 0x48
INFO  [muorb] SLPI: icp10100 #0 on I2C bus 5

INFO  [muorb] SLPI: Ok executing command: icp10100 start -I -b 5
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26486020, current timestamp 26486021
INFO  [qshell] qshell return value timestamp: 26486020, local time: 26487682
INFO  [uorb] Advertising remote topic sensor_mag
INFO  [qshell] Send cmd: 'modalai_esc start'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: modalai_esc start
INFO  [muorb] SLPI: Creating qurt thread wq_hp_default

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_hp_default with tid 73
INFO  [uorb] Advertising remote topic sensor_baro
INFO  [uorb] Advertising remote topic test_motor
INFO  [muorb] SLPI: Ok executing command: modalai_esc start
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26546800, current timestamp 26546801
INFO  [muorb] SLPI: Opened UART ESC device
INFO  [qshell] qshell return value timestamp: 26546800, local time: 26548152
INFO  [qshell] Send cmd: 'mixer load /dev/uart_esc quad_x.main.mix'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: mixer load /dev/uart_esc quad_x.main.mix
INFO  [muorb] SLPI: Creating qurt thread wq_rate_ctrl

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_rate_ctrl with tid 71
INFO  [muorb] SLPI: Ok executing command: mixer load /dev/uart_esc quad_x.main.mix
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26609932, current timestamp 26609933
INFO  [qshell] qshell return value timestamp: 26609932, local time: 26611050
INFO  [uorb] Advertising remote topic actuator_outputs
INFO  [uorb] Advertising remote topic multirotor_motor_limits
INFO  [qshell] Send cmd: 'voxlpm start -X -b 2'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: voxlpm start -X -b 2
INFO  [muorb] SLPI: Creating qurt thread wq_I2C2

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_I2C2 with tid 4169
INFO  [muorb] SLPI: *** I2C Device ID 0x784411 7881745
INFO  [uorb] Advertising remote topic battery_status
INFO  [muorb] SLPI: voxlpm #0 on I2C bus 2 (external)

INFO  [muorb] SLPI: Ok executing command: voxlpm start -X -b 2
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26674290, current timestamp 26674291
INFO  [qshell] qshell return value timestamp: 26674290, local time: 26675325
INFO  [uorb] Advertising remote topic power_monitor
Starting Holybro GPS
INFO  [qshell] Send cmd: 'gps start -d 7 -b 115200'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: gps start -d 7 -b 115200
INFO  [muorb] SLPI: Creating qurt thread gps

INFO  [muorb] SLPI: Successfully created px4 task PX4_gps with tid 70
INFO  [muorb] SLPI: Ok executing command: gps start -d 7 -b 115200
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26712883, current timestamp 26712884
INFO  [qshell] qshell return value timestamp: 26712883, local time: 26713903
INFO  [qshell] Send cmd: 'px4io detect'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: px4io detect
INFO  [muorb] SLPI: serial port fd 2
ERROR [muorb] SLPI: px4io read failed
ERROR [muorb] SLPI: px4io io_reg_get(0,0,1): data error -5
ERROR [muorb] SLPI: IO not installed
ERROR [muorb] SLPI: Detection attempt 2 failed
ERROR [muorb] SLPI: Detection attempt 1 failed
ERROR [muorb] SLPI: Detection attempt 0 failed
ERROR [muorb] SLPI: Failed to execute command: px4io detect
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26777758, current timestamp 26777759
INFO  [qshell] cmd returned with: -17
INFO  [qshell] qshell return value timestamp: 26777758, local time: 26778378
ERROR [qshell] Command failed
M0065 not detected, starting Spektrum RC driver
INFO  [qshell] Send cmd: 'spektrum_rc start -d 8'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: spektrum_rc start -d 8
INFO  [muorb] SLPI: Creating qurt thread spektrum_rc_main

INFO  [muorb] SLPI: Successfully created px4 task PX4_spektrum_rc_main with tid 67
INFO  [muorb] SLPI: Ok executing command: spektrum_rc start -d 8
INFO  [muorb] SLPI: Sending qshell retval with timestamp 26822566, current timestamp 26822566
INFO  [qshell] qshell return value timestamp: 26822566, local time: 26823292
INFO  [qshell] Send cmd: 'sensors start'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: sensors start
INFO  [muorb] SLPI: Creating qurt thread wq_nav_and_controllers

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_nav_and_controllers with tid 66
INFO  [muorb] SLPI: Ok executing command: sensors start
INFO  [muorb] SLPI: Sending qshell retval with timestamp 27885493, current timestamp 27885494
INFO  [uorb] Advertising remote topic vehicle_angular_acceleration
INFO  [uorb] Advertising remote topic vehicle_angular_velocity
INFO  [qshell] qshell return value timestamp: 27885493, local time: 27890054
INFO  [muorb] SLPI: Creating qurt thread wq_INS0

INFO  [muorb] SLPI: Successfully created px4 task PX4_wq_INS0 with tid 65
INFO  [uorb] Advertising remote topic vehicle_imu
INFO  [uorb] Advertising remote topic vehicle_imu_status
INFO  [uorb] Advertising remote topic sensors_status_imu
INFO  [uorb] Advertising remote topic vehicle_acceleration
INFO  [uorb] Advertising remote topic vehicle_air_data
INFO  [uorb] Advertising remote topic sensor_selection
INFO  [uorb] Advertising remote topic sensor_combined
INFO  [qshell] Send cmd: 'ekf2 start'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: ekf2 start
INFO  [muorb] SLPI: Ok executing command: ekf2 start
INFO  [muorb] SLPI: Sending qshell retval with timestamp 28080230, current timestamp 28080231
INFO  [qshell] qshell return value timestamp: 28080230, local time: 28081490
INFO  [uorb] Advertising remote topic ekf2_timestamps
INFO  [qshell] Send cmd: 'mc_pos_control start'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: mc_pos_control start
INFO  [muorb] SLPI: Ok executing command: mc_pos_control start
INFO  [muorb] SLPI: Sending qshell retval with timestamp 28141872, current timestamp 28141873
INFO  [qshell] qshell return value timestamp: 28141872, local time: 28143606
INFO  [qshell] Send cmd: 'mc_att_control start'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: mc_att_control start
INFO  [muorb] SLPI: Ok executing command: mc_att_control start
INFO  [muorb] SLPI: Sending qshell retval with timestamp 28193889, current timestamp 28193890
INFO  [qshell] qshell return value timestamp: 28193889, local time: 28194908
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: mc_rate_control start
INFO  [qshell] Send cmd: 'mc_rate_control start'
INFO  [muorb] SLPI: Ok executing command: mc_rate_control start
INFO  [muorb] SLPI: Sending qshell retval with timestamp 28277320, current timestamp 28277321
INFO  [qshell] qshell return value timestamp: 28277320, local time: 28277781
INFO  [qshell] Send cmd: 'mc_hover_thrust_estimator start'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: mc_hover_thrust_estimator start
INFO  [muorb] SLPI: Ok executing command: mc_hover_thrust_estimator start
INFO  [muorb] SLPI: Sending qshell retval with timestamp 28316740, current timestamp 28316741
INFO  [qshell] qshell return value timestamp: 28316740, local time: 28317757
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [qshell] Send cmd: 'land_detector start multicopter'
INFO  [muorb] SLPI: qshell gotten: land_detector start multicopter
INFO  [muorb] SLPI: Ok executing command: land_detector start multicopter
INFO  [muorb] SLPI: Sending qshell retval with timestamp 28355231, current timestamp 28355232
INFO  [qshell] qshell return value timestamp: 28355231, local time: 28356012
INFO  [uorb] Advertising remote topic vehicle_land_detected
INFO  [muorb] SLPI: 28570980: reset position to last known position
INFO  [muorb] SLPI: 28570980: reset velocity to zero
INFO  [uorb] Advertising remote topic vehicle_local_position
INFO  [uorb] Advertising remote topic vehicle_odometry
INFO  [uorb] Advertising remote topic estimator_states
INFO  [uorb] Advertising remote topic estimator_status
INFO  [uorb] Advertising remote topic estimator_status_flags
INFO  [uorb] Advertising remote topic estimator_innovations
INFO  [uorb] Advertising remote topic estimator_innovation_test_ratios
INFO  [uorb] Advertising remote topic estimator_innovation_variances
INFO  [dataman] Unknown restart, data manager file '/data/px4/dataman' size is 11798680 bytes
INFO  [muorb] SLPI: Advertising remote topic position_setpoint_triplet
INFO  [commander] LED: open /dev/led0 failed (22)
INFO  [muorb] SLPI: Advertising remote topic led_control
INFO  [muorb] SLPI: Advertising remote topic tune_control
INFO  [PreFlightCheck] Failed EKF health preflight check while waiting for filter to settle
INFO  [muorb] SLPI: Advertising remote topic vehicle_control_mode
INFO  [muorb] SLPI: Advertising remote topic vehicle_status
INFO  [muorb] SLPI: Advertising remote topic actuator_armed
INFO  [uorb] Advertising remote topic rate_ctrl_status
INFO  [uorb] Advertising remote topic actuator_controls_0
INFO  [muorb] SLPI: Advertising remote topic commander_state
INFO  [muorb] SLPI: Advertising remote topic vehicle_status_flags
INFO  [muorb] SLPI: Advertising remote topic vehicle_command
INFO  [commander] Handling Commander command 176
INFO  [muorb] SLPI: Advertising remote topic vehicle_command_ack
INFO  [mavlink] mode: Onboard, data rate: 100000 B/s on udp port 14556 remote port 14557
INFO  [muorb] SLPI: Marking DeviceNode(vehicle_command) as advertised in process_remote_topic
INFO  [uorb] Advertising remote topic estimator_sensor_bias
INFO  [px4] Startup script returned successfully
pxh> INFO  [muorb] SLPI: Advertising remote topic telemetry_status
INFO  [muorb] SLPI: 34702200: EKF aligned, (baro hgt, IMU buf: 11, OBS buf: 8)
INFO  [uorb] Advertising remote topic vehicle_attitude
INFO  [uorb] Advertising remote topic vehicle_attitude_setpoint
INFO  [uorb] Advertising remote topic vehicle_rates_setpoint

      Inside the pxh console, we ran the gps status command and got:

      INFO  [gps] not running
Command 'gps' failed, returned -1.

      I find this strange since when we ran the voxl-px4 service it had the start command for the gps. Since gps was not running, I decided to test again the gps start by doing gps stop and then gps start -d 7 -b 115200, that appeared on the output of ```voxl-px4``. The console output was:

      ERROR [gps] GPS: failed to open serial port: 7 err: 2

      We also tried the same with qshell.
      qshell gps status outputted:

      pxh> qshell gps status
INFO  [qshell] Send cmd: 'gps status'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: gps status
INFO  [muorb] SLPI: Main GPS
INFO  [muorb] SLPI: protocol: UBX
INFO  [muorb] SLPI: status: NOT OK, port: 6, baudrate: 115200
INFO  [muorb] SLPI: sat info: disabled
INFO  [muorb] SLPI: rate reading: 		     0 B/s
INFO  [muorb] SLPI: Ok executing command: gps status
INFO  [muorb] SLPI: Sending qshell retval with timestamp 318302556, current timestamp 318302557
INFO  [qshell] qshell return value timestamp: 318302556, local time: 318308860

      We also tried to stop and run it again with qshell gps stop and qshell gps start.

      After this, the output of qshell gps status was:

      pxh> qshell gps status
INFO  [qshell] Send cmd: 'gps status'
INFO  [muorb] SLPI: Marking DeviceNode(qshell_req) as advertised in process_remote_topic
INFO  [muorb] SLPI: qshell gotten: gps status
INFO  [muorb] SLPI: Main GPS
INFO  [muorb] SLPI: protocol: UBX
INFO  [muorb] SLPI: status: OK, port: 6, baudrate: 115200
INFO  [muorb] SLPI: sat info: disabled
INFO  [muorb] SLPI: rate reading: 		   695 B/s
INFO  [muorb] SLPI: rate position: 		  5.00 Hz
INFO  [muorb] SLPI: rate velocity: 		  5.00 Hz
INFO  [muorb] SLPI: rate publication:		  5.00 Hz
INFO  [muorb] SLPI: rate RTCM injection:	  0.00 Hz
INFO  [muorb] SLPI:  sensor_gps_s

INFO  [muorb] SLPI: 	timestamp: 405957015  (0.197956 seconds ago)

INFO  [muorb] SLPI: 	time_utc_usec: 0

INFO  [muorb] SLPI: 	lat: 0

INFO  [muorb] SLPI: 	lon: 0

INFO  [muorb] SLPI: 	alt: -17000

INFO  [muorb] SLPI: 	alt_ellipsoid: 0

INFO  [muorb] SLPI: 	s_variance_m_s: 1000.0001

INFO  [muorb] SLPI: 	c_variance_rad: 3.1416

INFO  [muorb] SLPI: 	eph: 4294967.5000

INFO  [muorb] SLPI: 	epv: 3772217.5000

INFO  [muorb] SLPI: 	hdop: 99.9900

INFO  [muorb] SLPI: 	vdop: 99.9900

INFO  [muorb] SLPI: 	noise_per_ms: 93

INFO  [muorb] SLPI: 	jamming_indicator: 30

INFO  [muorb] SLPI: 	vel_m_s: 0.0000

INFO  [muorb] SLPI: 	vel_n_m_s: 0.0000

INFO  [muorb] SLPI: 	vel_e_m_s: 0.0000

INFO  [muorb] SLPI: 	vel_d_m_s: 0.0000

INFO  [muorb] SLPI: 	cog_rad: 0.0000

INFO  [muorb] SLPI: 	timestamp_time_relative: 0

INFO  [muorb] SLPI: 	heading: -nan

INFO  [muorb] SLPI: 	heading_offset: 0.0000

INFO  [muorb] SLPI: 	fix_type: 0

INFO  [muorb] SLPI: 	jamming_state: 0

INFO  [muorb] SLPI: 	vel_ned_valid: False

INFO  [muorb] SLPI: 	satellites_used: 0

INFO  [muorb] SLPI: Ok executing command: gps status
INFO  [muorb] SLPI: Sending qshell retval with timestamp 406155973, current timestamp 406155974
INFO  [qshell] qshell return value timestamp: 406155973, local time: 406158054

      Any ideia of what the problem could be?

      I also noticed the following errors on the voxl-px4 output:

      ERROR [muorb] SLPI: px4io read failed
ERROR [muorb] SLPI: px4io io_reg_get(0,0,1): data error -5
ERROR [muorb] SLPI: IO not installed
ERROR [muorb] SLPI: Detection attempt 2 failed
ERROR [muorb] SLPI: Detection attempt 1 failed
ERROR [muorb] SLPI: Detection attempt 0 failed
ERROR [muorb] SLPI: Failed to execute command: px4io detect

      Is this normal?

      Thank you.

      Eric KatzfeyE 3 Replies Last reply Reply Quote 0
      • Eric KatzfeyE
        Eric Katzfey ModalAI Team @Andre Moura
        last edited by

        @andremoura Yes, the errors related to px4io detection are expected since you do not have a px4io unit attached to the drone. And yes, you have to interact with things on the DSP (where the GPS driver runs) with qshell as you already figured out. Do you have any other Sentinel drones that you can compare against? Or other types of drones with GPS to compare against? When you are able to get 9 to 12 satellites what does qshell gps status show? It does appear to be wired up correctly as sometimes it is obviously communicating with the GPS unit.

        A 1 Reply Last reply Reply Quote 0
        • Eric KatzfeyE
          Eric Katzfey ModalAI Team @Andre Moura
          last edited by Eric Katzfey

          @andremoura It looks like there are at least 2 different issues here. One is that when you do see it working it has poor performance and doesn't get a lock. That is why I wanted to compare against other drones or other GPS units. If other units are working fine and this one isn't then maybe it's a faulty unit. If they all have poor performance then maybe it's something about the test location.

          A 1 Reply Last reply Reply Quote 0
          • Eric KatzfeyE
            Eric Katzfey ModalAI Team @Andre Moura
            last edited by

            @andremoura The other issue appears to be that you don't always get the driver to communicate with the GPS unit on startup. The start line in /etc/modalai/voxl-px4.config is qshell gps start -d 7 -b 115200. When you did qshell gps stop and then qshell gps start was it started with qshell gps start -d 7 -b 115200 or just qshell gps start?

            A 1 Reply Last reply Reply Quote 0
            • A
              Andre Moura @Eric Katzfey
              last edited by

              @Eric-Katzfey We don't have any other Sentinel drones. We have other drones with GPS, that detect at least the same or higher number of satellites but they all are able to GPS lock.

              When we had that number of satellites, the qshell gps status seemed ok with number of satellites, latitude and longitude, but we aren't able to replicate that test right now because of bad weather conditions.

              1 Reply Last reply Reply Quote 0
              • A
                Andre Moura @Eric Katzfey
                last edited by

                @Eric-Katzfey I will test the Sentinel drone on a new better location next week, if weather gets better, and I will get back to you.

                1 Reply Last reply Reply Quote 0
                • A
                  Andre Moura @Eric Katzfey
                  last edited by

                  @Eric-Katzfey GPS mostly hasn't beeen working on startup again.

                  We started it with qshell gps start, but we also tested qshell gps start -d 7 -b 115200. Both commands only worked a few times, we are not able to consistently start the GPS, having to stop and start again the service a few times before it works.

                  Eric KatzfeyE 1 Reply Last reply Reply Quote 0
                  • Eric KatzfeyE
                    Eric Katzfey ModalAI Team @Andre Moura
                    last edited by

                    @andremoura Is the LED on top of the unit (multicolor LED) coming on?

                    A 1 Reply Last reply Reply Quote 0
                    • A
                      Andre Moura @Eric Katzfey
                      last edited by Andre Moura

                      @Eric-Katzfey said in GPS not working:

                      @andremoura Is the LED on top of the unit (multicolor LED) coming on?

                      Yes, every time voxl-px4 is running.

                      Eric KatzfeyE 1 Reply Last reply Reply Quote 0
                      • Eric KatzfeyE
                        Eric Katzfey ModalAI Team @Andre Moura
                        last edited by

                        @andremoura Okay, good. Holybro changed some of the components in their unit at one point and if that LED wasn't coming on it could indicate that it was one of the older units. But since it is on that indicates to me that it is the correct version of the Holybro unit.

                        1 Reply Last reply Reply Quote 0
                        • A
                          Andre Moura
                          last edited by

                          @Eric-Katzfey Ok, new find! It seems that when voxl-px4 runs, the GPS service isn't able to start immediately, but if we wait a for a bit and start it manually, it works.

                          Seems like something isn't ready to start immediately after voxl-px4.

                          Eric KatzfeyE 1 Reply Last reply Reply Quote 0
                          • Eric KatzfeyE
                            Eric Katzfey ModalAI Team @Andre Moura
                            last edited by

                            @andremoura Interesting! Okay, how do you accomplish that? Do you mean you are stopping the service and then starting voxl-px4 later manually or you are leaving voxl-px4 service enabled but commenting out the gps start line in /etc/modalai/voxl-px4.config?

                            A 1 Reply Last reply Reply Quote 0
                            • A
                              Andre Moura @Eric Katzfey
                              last edited by

                              @Eric-Katzfey We are stopping the GPS service manually (qshell gps stop) and then starting it later manually (qshell gps start), not the voxl-px4.

                              Do you want us to do the same test with commenting the gps start line in /etc/modalai/voxl-px4.config?

                              Eric KatzfeyE 1 Reply Last reply Reply Quote 0
                              • Eric KatzfeyE
                                Eric Katzfey ModalAI Team @Andre Moura
                                last edited by

                                @andremoura Actually, can you try removing the -d 7 -b 115200 from the gps start line in /etc/modalai/voxl-px4.config and see if that changes anything? Thanks for trying all this stuff out!

                                A 2 Replies Last reply Reply Quote 0
                                • A
                                  Andre Moura @Eric Katzfey
                                  last edited by

                                  @Eric-Katzfey Hello, today I tested removing -d 7 -b 115200 from /etc/modalai/voxl-px4.config and it seems like the GPS service is working correctly on startup. I'm still going to test if I can get more fixed satellites and GPS lock on a new location with more open space and then get back to this post with more information.

                                  D 1 Reply Last reply Reply Quote 0
                                  • A
                                    Andre Moura @Eric Katzfey
                                    last edited by

                                    @Eric-Katzfey On the new location, we were able to get GPS lock after fixing 12 satellites, which allowed for take-off. During flight we reached 19 satellites at one point. Getting GPS lock with this sensor is a bit challenging, our previous location didn't have that many obstructions, but everything seems to be working.

                                    Eric KatzfeyE 1 Reply Last reply Reply Quote 0
                                    • Eric KatzfeyE
                                      Eric Katzfey ModalAI Team @Andre Moura
                                      last edited by

                                      @Andre-Moura Thanks for all of the testing! We really appreciate it, this is all great feedback! It seems that Holybro may have changed the default configuration of the units and that could be why it wasn't coming up properly.

                                      1 Reply Last reply Reply Quote 1
                                      • D
                                        daniel @Andre Moura
                                        last edited by

                                        @Andre-Moura We have same issue here but we try to remove -d 7 -b 115200 from /etc/modalai/voxl-px4.config is still not working. Did you modify thr code like this?
                                        efbb3413-b105-4c9e-9c2e-0f2349389742-image.png

                                        Removing the 115200 baud rate is still not see GPS log.
                                        ad127a05-5515-4a8f-9e1b-af96fd7a9625-image.png

                                        A 1 Reply Last reply Reply Quote 0
                                        • A
                                          Andre Moura @daniel
                                          last edited by

                                          @daniel I think that's all I did, but here is my /etc/modalai/voxl-px4.config, in case you want to look for any differences:

                                          #!/bin/sh
# PX4 commands need the 'px4-' prefix in bash.
# (px4-alias.sh is expected to be in the PATH)
. px4-alias.sh

# Figure out what platform we are running on.

# Eventually there will be a utility called voxl-platform that will
# return the platform tag or an error code. This utility is not yet
# ubiquitous so it may be that it isn't available. Trying to call a
# non existent program will generate an error code by the OS. If the
# program exists and doesn't return an error code then use the results.
PLATFORM=`/usr/bin/voxl-platform 2> /dev/null`
RETURNCODE=$?
if [ $RETURNCODE -ne 0 ]; then
    # If we couldn't get the platform from the voxl-platform utility then check
    # /etc/version to see if there is an M0052 substring in the version string. If so,
    # then we assume that we are on M0052. Otherwise assume M0054.
    VERSIONSTRING=$(</etc/version)
    M0052SUBSTRING="M0052"
    if [[ "$VERSIONSTRING" == *"$M0052SUBSTRING"* ]]; then
        PLATFORM="M0052"
    else
        PLATFORM="M0054"
    fi
fi

# We can only run on M0052 or M0054 so exit with error if that is not the case
if [ $PLATFORM = "M0052" ]; then
    /bin/echo "Running on M0052"
    if [ "$RC" == "CRSF" ]; then
        /bin/echo "Error, crossfire not supported on M0052!"
        exit 0
    fi
elif [ $PLATFORM = "M0054" ]; then
    /bin/echo "Running on M0054"
else
    /bin/echo "Error, cannot determine platform!"
    exit 0
fi

uorb start
muorb start

# In order to just exit after starting the uorb / muorb modules define
# the environment variable MINIMAL_PX4. (e.g. export MINIMAL_PX4=1)
# This is useful for testing / debug where you may want to start drivers
# and modules manually from the px4 command shell
if [ ! -z $MINIMAL_PX4 ]; then
    /bin/echo "Running minimal script"
    exit 0
fi

# Sleep a little here. A lot happens when the uorb and muorb start
# and we need to make sure that it all completes successfully to avoid
# any possible race conditions.
/bin/sleep 1

# IMU (accelerometer / gyroscope)
# Start this first because it gets the high rate interrupts coming in to the
# DSP. Without this the DSP will oversleep and miss critical timeouts.
# TODO: Why is that the case?
if [ "$IMU" == "ROTATE_IMU_YAW_180" ]; then
    /bin/echo "Starting IMU driver with yaw 180 rotation"
    qshell icm42688p start -s -R 4
else
    qshell icm42688p start -s
fi

/bin/sleep 1

# Load in all of the parameters that have been saved in the file
param load

# Start logging and use timestamps for log files when possible.
# Add the "-e" option to start logging immediately. Default is
# to log only when armed
logger start -t

# We do not change the value of SYS_AUTOCONFIG but if it does not
# show up as used then it is not reported to QGC and we get a
# missing parameter error.
param touch SYS_AUTOCONFIG

# Start all of the device drivers on DSP

# Magnetometer
if [ "$GPS" == "MATEK" ]; then
    # Use this line for the magnetometer in the Matek Systems M8Q-5883 module
    /bin/echo "Starting Mateksys M8Q-5883 magnetometer"
    qshell qmc5883l start -R 10 -X -b 1
elif [ "$GPS" == "HERE3" ]; then
    # Use this line for the magnetometer in the Here3 GPS module
    /bin/echo "Starting Here3 ak09916 magnetometer"
    qshell ak09916 start -R 2 -X
else
    # Use this line for the magnetometer in the Holybro GPS module
    /bin/echo "Starting Holybro magnetometer"
    qshell ist8310 start -R 10 -X -b 1
fi

# LED driver for the Pixhawk 4 GPS module
# Older units have i2c address 0x39 (57) and newer ones 0x38 (56)
# M0054 only supports the newer one. M0052 can support either.
if [ $PLATFORM = "M0052" ]; then
    qshell rgbled_ncp5623c start -X -b 1 -f 400 -a 57
fi
if [ "$GPS" == "HOLYBRO" ]; then
    /bin/echo "Starting Holybro LED driver"
    qshell rgbled_ncp5623c start -X -b 1 -f 400 -a 56
elif [ "$GPS" == "HERE3" ]; then
    # Use this line for the Here3 GPS module LED controller
    /bin/echo "Starting Here3 LED"
    qshell rgbled start -X -f 400
fi

# Barometer
qshell icp10100 start -I -b 5

# ESC driver
# We start this even if there is a PX4IO module. If there is
# a PX4IO (M0065) module it will be plugged into the RC port
# and so this driver will output commands on an empty port.
qshell modalai_esc start
qshell mixer load /dev/uart_esc quad_x.main.mix

# APM power monitor
qshell voxlpm start -X -b 2

# On M0052 the GPS and RC drivers run on the apps processor
if [ $PLATFORM = "M0052" ]; then
    # Pixhawk 4 GPS module
    gps start -d /dev/ttyHS2

    # RC input may be coming via either an external M0065 (aka px4io) module
    # or a directly attached Spektrum receiver. First see if the M0065 is detected.
    px4io detect
    PX4IO_STATUS=$?
    /bin/echo "PX4IO detect returned value $PX4IO_STATUS"
    if [ $PX4IO_STATUS -eq 0 ]; then
        /bin/echo "Found M0065, starting px4io"
        # On M0052 px4io only supports RC input, not PWM output
        px4io start
    else
        /bin/echo "M0065 not detected, starting Spektrum RC driver"
        spektrum_rc start -d /dev/ttyHS1
    fi
# On M0054 the GPS and RC drivers run on SLPI DSP
else
    if [ "$GPS" == "MATEK" ]; then
        # Use this gps start line instead for Matek Systems M8Q-5883 module
        /bin/echo "Starting Mateksys M8Q-5883 GPS"
        qshell gps start
    elif [ "$GPS" == "HERE3" ]; then
        # Use this line for the Here3 GPS module
        /bin/echo "Starting Here3 GPS"
        qshell gps start
    else
        # Only the newer Holybro unit is supported on M0054
        /bin/echo "Starting Holybro GPS"
        qshell gps start
    fi

    # If RC is TBS Crossfire then start its driver.
    # Otherwise, it could be either a directly connected Spektrum receiver
    # or an external M0065 (aka px4io) module.
    if [ "$RC" == "CRSF_MAV" ]; then
        /bin/echo "Starting TBS crossfire RC - MAV Mode"
        qshell tbs_crossfire start -m -p 7 -b 115200
    elif [ "$RC" == "CRSF_RAW" ]; then
        /bin/echo "Starting TBS crossfire RC - CRSF Mode"
        qshell tbs_crossfire start -c -p 7 -b 250000
    else
        qshell px4io detect
        PX4IO_STATUS=$?
        if [ $PX4IO_STATUS -eq 0 ]; then
            /bin/echo "Found M0065, starting px4io"
            # On M0054 we also support PWM output from M0065 (aka PX4IO)
            # If there are no pwm escs then that connector will be empty.
            qshell px4io start
            qshell px4io recovery
            qshell mixer load /dev/px4io quad_x_io.main.mix

            sleep 1
            qshell pwm rate -c 1234 -r 400
			qshell pwm disarmed -c 1234 -p 900
			qshell pwm min -c 1234 -p 1060
			qshell pwm max -c 1234 -p 2000
            qshell pwm failsafe -c 1234 -p -1 -d /dev/px4io
        else
            /bin/echo "M0065 not detected, starting Spektrum RC driver"
            qshell spektrum_rc start -d 8
        fi
    fi
fi

/bin/sleep 1

# Start all of the processing modules on DSP

qshell sensors start
qshell ekf2 start
qshell mc_pos_control start
qshell mc_att_control start
qshell mc_rate_control start
qshell mc_hover_thrust_estimator start
qshell land_detector start multicopter

/bin/sleep 1

# Start all of the processing modules on the applications processor

rc_update start

dataman start

navigator start

commander start
commander mode manual

# This is needed for altitude and position hold modes
flight_mode_manager start

# Start our service to update system time from GPS
modalai_gps_timer start

# As of 1.4.11 mavlink configuration has been changed!!! All communications are
# now done via the mavlink server and voxl-vision-px4!!!
param set MAV_BROADCAST 0

if [ "$RC" == "CRSF_MAV" ]; then
    # Slow everything way down if we are using TBS Crossfire
    mavlink start -a -x -u 14556 -o 14557 -r 10000 -n lo -m minimal

    /bin/sleep 1
else
    mavlink start -x -u 14556 -o 14557 -r 100000 -n lo -m onboard

    /bin/sleep 1

    # slow down some of the fastest streams in onboard mode
    mavlink stream -u 14556 -s HIGHRES_IMU -r 10
    mavlink stream -u 14556 -s ATTITUDE -r 10
    mavlink stream -u 14556 -s ATTITUDE_QUATERNION -r 10
    # speed up rc_channels
    mavlink stream -u 14556 -s RC_CHANNELS -r 50

    /bin/sleep 1
fi

if [ $PLATFORM = "M0052" ]; then
    # Start up the IMU server to support VIO. This is done differently on M0054
    imu_server start
fi

mavlink boot_complete

# For now we use a mavlink bridge for TBS Crossfire support
if [ "$RC" == "CRSF_MAV" ]; then
    mavlink_bridge start
fi

# Optional MSP OSD driver for DJI goggles
# This is only supported on M0054 (with M0125 accessory board)
if [ $PLATFORM = "M0054" ]; then
    if [ "$OSD" == "OSD" ]; then
        /bin/echo "Starting OSD driver"
        msp_osd start -d /dev/ttyHS1
    fi
fi

                                          If your config is like this and it still doesn't work, maybe @Eric-Katzfey can help you better.

                                          D 1 Reply Last reply Reply Quote 0
                                          • D
                                            daniel @Andre Moura
                                            last edited by

                                            @Andre-Moura Thank You! We fixed our GPS setting problem.

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Powered by NodeBB | Contributors