ModalAI Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Register
    • Login

    Stereo Camera Calibration update?

    Ask your questions right here!
    3
    11
    815
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • KrisK
      Kris
      last edited by Kris

      Cannot calibrate my tracking camera either.
      My image looks different from the example pic for calibrating the tracking camera as well.
      Tracking Calibration_r.png
      Everthing inside the red rectrangle appears to be distorted, while everything outside appears normal (black and white).

      voxl-calibrate-camera tracking -f -s 6x8 -l 0.040
      
      1 Reply Last reply Reply Quote 0
      • KrisK
        Kris
        last edited by

        Is this issue only deriving from my side (setup/config),
        Or is this caused by VOXL Portal or server side?

        1 Reply Last reply Reply Quote 0
        • ?
          A Former User
          last edited by

          That thresholding is intentional to give the users an idea of what the calibrator is looking at. We perform a threshold over the desired rectangle then search for the checkerboard, so there's likely a lighting issue if you can't see the corners well enough. This can be fixed either with a bright overhead light or using you phone flashlight to light up the corners that are struggling.

          KrisK 1 Reply Last reply Reply Quote 0
          • KrisK
            Kris @Guest
            last edited by Kris

            @Alex-Gardner Thank you, I will try the tracking camera calibration with different lighting.
            What about the stereo camera calibration? Why am I not given the opportunity to hit enter in the terminal after both cameras have gone through their 10 extrinsic’s (20 calibration extrinsic’s)?

            extrinic 21
            21-1.png

            extrinic 22
            22-1.png

            extrinic 23 - cannot complete
            23-1.png

            1 Reply Last reply Reply Quote 0
            • ?
              A Former User
              last edited by

              The targets that you were using are the intrinsics targets used to calibrate the lens of each camera, we used to have the extrinsics cal be manual entry, but we were eventually able to add targets to these as well, on any of the standard platforms that we sell these targets should all be attainable. If the checkerboard is out of frame on the second camera then there's an issue and your cameras are much more angled than they should be on our platforms, if you can see the board fine but it's not being recognized by the calibrator, then it's either a focus or a lighting issue. It looks like your setup has pretty bright lights directly behind the checkerboard, which could be causing problems for the thresholder, try to make sure that the primary light source in the area is shining on the board.

              KrisK 2 Replies Last reply Reply Quote 1
              • KrisK
                Kris
                last edited by

                I tried the tracking calibration with more and better lighting. This still did not allow me to pass the first extrinic (red box). I was able to get the rainbow colored points to light up (constantly) and was able to even get the red extrinic calibration box to change to green for about 3-4 seconds. However, it could not pass the first extrinic.

                1 Reply Last reply Reply Quote 0
                • KrisK
                  Kris @Guest
                  last edited by

                  @Alex-Gardner In the area that I am conducting the calibration in, there are actually another pair of fluorescent lights out of the camera view ( 4 sets of fluorescent light structures total). I am calibrating directly under two fluorescent light stuctures that are not viewable in the images I have provided.
                  About angle of the cameras, I am using the VOXL CAM frame (like in the Seeker). This is the way it was delivered to me from ModalAI. How can I change the angle on the cameras when they are mounted inside the green frame? Is this possible?

                  1 Reply Last reply Reply Quote 0
                  • KrisK
                    Kris
                    last edited by Kris

                    Should I just manually enter the extrinic calibration for stereo and tracking cameras? If so, how can I do this?
                    Or is there a different platform I can use to calibrate these cameras?

                    1 Reply Last reply Reply Quote 0
                    • KrisK
                      Kris @Guest
                      last edited by

                      Thank you Alex, I was finally able to calibrate the stereo cameras and the tracking camera.
                      You were spot on with the issue. It was because of the angle and focus on the stereo cameras and the angle on the tracking camera.

                      modaltbM 1 Reply Last reply Reply Quote 1
                      • modaltbM
                        modaltb ModalAI Team @Kris
                        last edited by

                        @Kris Thanks for the feedback!

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Powered by NodeBB | Contributors