Subcategories

• VOXL 2 Mini

  VOXL 2 Support Forum

  42
  Topics
  229
  Posts

  M

  @milanerd The added capacitance helps VOXL 2 Mini's USB port achieve USB 3 speeds. We don't have that adapter to confirm a fix for your issue, but with the cable the link should transfer much faster

• VOXL 2

  VOXL 2 Support Forum

  488
  Topics
  2720
  Posts

  A

  @david-moro and @TomP ,

  I am curious about your requirements for digital image stabilization, since there are a few approaches, as you know some use IMU, some dont.. some support large stabilization range, others only remove shakiness (for example smartphones, which use optical and digital stabilization vs a really wide field of view camera that is able to perform stabilization in the full flight envelope).

  Also, image stabilization for FPV is different than for recording pretty videos - not only the range of motion may be different, but also latency, etc.

  It would help if you (and anyone else) let us know what (roughly) you are looking for in digital image stabilization, so that we can consider that use case as we are designing the new feature.

  As we get closer to a beta release, we will definitely welcome beta testing and feedback. Thanks!

  Alex

• VOXL Flight
  74
  Topics
  291
  Posts

  E

  @boga Sorry, yes, I was referring to VOXL 2.

• VOXL
  119
  Topics
  560
  Posts

  A

  @qqa , we have document how to achieve folder-level encryption on VOXL2 here : https://docs.modalai.com/enabling-file-encryption/ . Please let us know if you have any other questions.

• Flight Core v2
  31
  Topics
  154
  Posts

  A

  @prawinsankar , can you please clarify which firmware you are talking about?

  If you are referring to PX4 and drivers for RC, you have to look at the specific driver for the RC and see how the baud rate is passed to the driver, typically as a param or launch argument when the PX4 module is loaded.

  Alex

• Flight Core
  36
  Topics
  135
  Posts

  T

  Unbricked! Here's some context/advice for anyone trying to do the same. If you purchased a cheapo STLINK V2 from Amazon as I did. Picture below...

  alt text

  $0 Fix:
  What may very well happen to ya, is the RESET pin doesn't work. In this case you will need a friend. With said friend, you must dilligently connect to the board using Under Reset Mode and Hardware Reset. The second your homie clicks the connect button, you, the bricker of the board must move your jumper cable from the RESET pin which is 3.3V to an open Ground, leave it for exactly 1 second, then move it back to RESET. This should work like a charm, but may require one or two tries to get the right timing. See instructions below.

  alt text

  $10 Fix:
  Program a Pico/Arduino to do your 1 second ground for you.

  $78 Fix:
  Buy the real STLINK V2.

• VOXL 2 IO

  VOXL 2 I/O (M0065) Support

  20
  Topics
  149
  Posts

  A

  @xav04 , yes, please see https://docs.modalai.com/voxl2-io-user-guide/

• Flight Core - ArduPilot
  3
  Topics
  12
  Posts

  P

  ok I found the problem...
  the Cube Serial inteface are driven by TXS0108E Level Shifter powered both side with 3.3 volt making it marginal for the Voxl Primary Serial interface. Switching to secondary interface on the Voxl made it work correctly.

  I sent a request for a change in the WIKI to reflect that configuration

  40f28124-b098-4482-a038-25c450b9df6c-image.png